Jump to content
SAU Community

Recommended Posts

to everybody who says put it on dyno,

I know this would be the best way to slove the problem but im the kind of guy that loves to solve problems myself and not just watch someone else do it. I would rather blow up the motor than have someone fix everything and not knowing exactly what was happening and what he did.  

The most fun about having a quick car is playing with it.

Thanks for all your help though

are you also the type of person who likes replacing thier own engine?

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

tomj,

yeah sure, love pulling motors in and out and pulling them apart. I have a snatch block hanging from my garage all year round. still, it does not beat sex, i don't have a wank over cars like some do.

Can anyone verify that my fuel pressure is too low (50psi) at 15psi boost?

cheers

50psi is about right.. stock rail pressure is 38psi + 15psi boost = 53psi.. which is close enough as BHdave is saying also.. I think you may be adding the standard boost pressure there in your mind to whatever you are thinking... the workshop manual is saying 37.5 + 7 (stock boost) = close enough to 45 :rofl: .. where as 15psi + 38 = 53psi..

why you are trying to run 14psi+ on a stock intercooled, stock turbo (I assume?), stock ecu, rb20 is beyond me a bit.. but you can try.

tomj,

        yeah sure, love pulling motors in and out and pulling them apart. I have a snatch block hanging from my garage all year round. still, it does not beat sex, i don't have a wank over cars like some do.

Can anyone verify that my fuel pressure is too low (50psi)  at 15psi boost?

cheers

im not having a dig, but why go through all these headaches when one run could save you so much time stress and maybe an engine.

50psi seems about right though

predator,

I have a 600*400*80mm front mount, standard turbo, yes i know but im just playing till i find a rb25 turbo.

I did a search and rang around and the fuel pressuse is supposed 2 be 45psi +/- boost, ie 37.5psi at idle, and should be 60psi at 15psi boost. I can clearly see it rise to 60, then fall off to 50 at the higher revs.

In goes another pump, yay.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • That's not a transistor --- it's marked ZD1 which makes it a zener diode. As to what the breakdown voltage is, not enough there to divine.
    • Hi all, Long time since I've posted here. Looking for some advice on what I can remove to further identify the cause of my issues.  I can move the passenger seat forward and back but the knob used to adjust the seat angle is pretty much free spinning, there's very little resistance.  Removing the side cover I can see that the chain is intact but the shaft for the adjustment spins without the gear attached to it moving.  What's my next step for disassembly here? Is this a common fault? Just being a little cautious as I didn't want to start removing bolts for a spring to fly out or something equally as stupid.  Cheers
    • The incentives are mostly the same, yes. Ethanol is cheap compared to the cost of doing 98-100 RON with crude oil alone. 87 to 93-94 AKI all with E10. In 2020 Canada mandated E10 as a part of their "renewable fuel standard" and is supposedly going to go to E15 in 2030. In California where there are only 8 refineries with two threatening to shut down next year it's been over 20 years now of E10 and 91 AKI maximum because there's just not enough refinery capacity or crude oil supply relative to the demand for premium unleaded fuel. And CARB's low carbon fuel standard means functionally none of the diesel available at the pump is made from crude oil anymore. It's almost all entirely 20% biodiesel blended with 80% renewable diesel (hydrotreated vegetable oil) now. The number of gasoline vehicles that support E15 or higher ethanol concentrations is surprisingly low, I can't imagine it being wise to play tricks like this without flex fuel sensors in most of the fleet.
    • It's almost certainly the same as the one next to it. Have a fish around amongst these hits https://www.google.com/search?q=surface+mount+transistor+m33&sca_esv=9cb49794e0b2005d&source=hp&ei=2vJ5aNjTB7Kw0PEPldnS8QM&iflsig=AOw8s4IAAAAAaHoA6qkfmF6XcygtrZ4Vu9f92NXF_RFd&ved=0ahUKEwjYqIPP7MWOAxUyGDQIHZWsND4Q4dUDCA8&uact=5&oq=surface+mount+transistor+m33&gs_lp=Egdnd3Mtd2l6IhxzdXJmYWNlIG1vdW50IHRyYW5zaXN0b3IgbTMzMgUQIRigATIFECEYoAEyBRAhGKABMgUQIRigAUjKCFAAWABwAHgAkAEAmAHfAaAB3wGqAQMyLTG4AQPIAQD4AQL4AQGYAgGgAuYBmAMAkgcDMi0xoAfMBLIHAzItMbgH5gHCBwMyLTHIBwU&sclient=gws-wiz
    • South Australia, which is hardly as far behind as the rest pf Oz makes out, and who is also not a paragon of progressiveness (read that as over-legislation) in the area of vehicle standards, has this to say on the subject: Adjustable coil-over suspension Aftermarket adjustable coil-over suspension components are suspension units that incorporate an external thread on the main body and corresponding threaded spring saddle that allows the vehicle's suspension height to be varied. If fitting aftermarket or coil-over suspension components you must submit an Application to modify a light motor vehicle form and a report from a light vehicle engineering signatory (LVES).
×
×
  • Create New...