Jump to content
SAU Community

Recommended Posts

I just had my accessory belts changed and the cooling system flushed and replaced coolant with Nissan Long Life Coolant.

Now when I drive it the car cuts out at random times. Happened 4 times today, once as I was just travelling normally, again when in traffic (on the freeway so in 1st gear), again once stopped at lights after going down freeway and again when turning corner into driveway. So all different conditions.

It used to cut out before when warm and stuck in freeway traffic but hadn't done that for a while.

I can't see how flushing the system and changing coolant could cause this problem.

Any ideas?

Cheers, Al

Yeah as in stalling and turns off without warning - the revs just die like I turned the key off

It got better today only stalled once on the way to work and twice on the way home.

I am thinking it could be something got wet when they flushed the radiator - would that cause the problem?

I have the factor BOV

I am thinking it could be something got wet when they flushed the radiator - would that cause the problem?

I have the factor BOV

Yeah definatly!

My Vl had the same problem - I could never find it and didn't want to spend any money, I just popped the bonnet on a really hot day and left it to dry for a few hours.

Allways did the trick - from working on the cooling system I'd say crank angle sensor maybe?

Worth unplugging everything and giving a spray with crc.

Maybe Air Flow meter plug?

Good luck!

Thanks for the replies and will try that on the weekend (hopefully it will be warm enough)

Stopped the problem on the way to work though just by putting the air-con on to keep the idle revs higher (this was after 3 stalls)

Cheers, Al

Check the idlin speed of ur car..should idle at 800 revs or so...

if it not then ur idle needs adjustin.

Where does the temperature gauge sit?

Does it idle rough ?

Cant see something wet bein the problem at this stage as the car engine would have dried out by now.

Red Sky,

This exact same thing happened to me in my R31. The sudden change of coolant has caused your system to break down more rapidly than with the water or low quality coolant you had in there.

Get the CO2 Sensor checked, and if its corroded/dirty get it cleaned. Get your water pump checked too. Should fix the problem.

Where does the temperature gauge sit?

Does it idle rough ?

Idle speed appears okay and the temperature gauge is normal.

Will get the O2 sensor, etc checked out though

Cheers, Al

Thanks again for the suggestions and it gives some things to try.

It hasn't really done it as much this week so maybe it was something that got wet or has just sorted itself out. It didn't like the 40 degree heat today though, nearly cut out a few times but didn't since the air-con was on.

To answer questions, it mainly stalls when slowing down to a stop such as on the freeway, stopping at lights although has done it when turning into my driveway (can't turn the damn thing since power steering disappears !!!)

owned

Haven't done the 100,000kms service yet as only done 77,000kms so far. Getting it serviced by an import specialist next time so will get them to check it all out then.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I mean it's a bit late to say "This won't have any tangible effect and it is not worth spending more than about three seconds on it, please just enjoy the car" But I said it anyway. Does the pod actually get any airflow in that position behind a bumper like that?
    • Hey guys - apologies for digging this up. Has this website been shutdown or is the outage temporary?
    • So, went shopping at Just Jap for things that might work for the intake  After some trial fitting there I ended up with a 3" x 45° silicone bend, a 3" x 300mm alloy straight, and a humped joiner, some minor trimming will be required to shorten some of the stuff, but nothing that is beyond my "ham fisted" skills The guy at Just Jap was most helpful as we had all sorts of joiners,  bends and stuff out trial fitting  Laying it out above the stuff in there it seems everything will fit nicely, and looking at it, it is probably the way I should have been looking at doing it from the beginning, probably..... In the end it is a front bar off job anyway to remove the original stuff behind the front bar that is taking up the required realestate needed, so maybe a Thursday or Friday job And because I'm a hopeless consumer, I grabbed some new steel wheel nuts, the current ones are a spline drive type with a "security" socket, that somehow someone keeps misplacing, the new ones are a basic black steel 17mm hex socket In other news: I just did my "final" tax return, I am now officially a old retired veteran pensioner, and I'm milking the system for all it's worth,  life is good
    • I hadn't thought about the variable power steering assist. Presumably, it will always be the same level of assist as you get in an S14. The R32/3/4 are either helliishly heavy (at low speeds) if the solenoid is not powered at all, or hellishly too light (at high speed) if it is powered all the time. I presume that it is PWM controlled on those cars. I hadn't thought about the S cars not having variable assist. ugh. What crappy plebby cars they must be!  
    • Hmm yeah that is a good point. It looks like it'll just bolt in with no real issue besides maybe the bushings being different. My other concern was that 2 pin plug that I assume is used in some way to control the rack solenoid depending on the speed signal from the ecu. The DMAX rack doesn't even have that plug though so, don't think it'll matter. Might just order the rack and see how it goes. Will update this when I figure something out
×
×
  • Create New...