Jump to content
SAU Community

NSW only Window tinting

Abo Bob

By Abo Bob,
in Group Buys

 Share

Recommended Posts

  • Replies 154
  • Created
  • Last Reply

Top Posters In This Topic

Popular Days

Top Posters In This Topic

Popular Days

Tommyk Veteran

Tommyk

Posted
Posted
Mine has bewen done too, satisfactory, at least i can open my two rear passenger windows, lol. HAHAHAH and my stoopid battery died out on me while robert was doing my tint

Haha yeh I spoke to Robert about that. Took him like what 30 mins to get your car out of the garage :D

locosam Contributor

locosam

Posted
Posted

I got mine done as well. I was right after E_Lu-SHuN. Was looking on while robert and e_lu-shun was trying to get the car started lol

Good guy, but very very busy. try make it on the prefered days.

But i found some very small bubbles in one tint :(

Its not bad, barely noticable, but i dunno how itll be in a few years time after opening and closing the window several hundred times. Might ring him a bit later and see what he says.

Overall though, still recommended :D

Thanks Sarpi for organising!

edit: forgot how to use english properly

lwells Grand Master

lwells

Posted
Posted
But i found some very small bubbles in one tint :D  

Its not bad, barely noticable, but i dunno how itll be in a few years time after opening and closing the window several hundred times. Might ring him a bit later and see what he says.

Give him a call: I remember one guy in the last group buy had a few bubbles and it was quickly fixed.

LW.

locosam Contributor

locosam

Posted
Posted

Yeah ill do that. He said to leave it for week to see how it goes, and then if theres any issues to call him. I work in north ryde, so its no hassles for me to go round there

Merli Grand Master

Merli

Posted
Posted
Merli - just send me an email as per one of my previous posts.

DONE!!!!!!!

P.S. Copy the email details into the first post so people don't have to search through all 4 pages to find it :( :kick:

Beer Baron Grand Master

Beer Baron

Posted
Posted
Ok we have 19 vehicles confirmed.  Keep your eye out for an email tomorrow.

The following people have not replied to pms or sent me an email but put themselves down as in.

mmmgtir

rOma

Endorean

GTR032

Malecki

MarkE

myr34

I know at least 3 of those above and expect their response in due course, MarkE certainly seemed keen (despite the misunderstanding :() so just a few others there that I don't know about.

Sorry for being a c unt with no reply :oops:

I am still in. I had being trying to hold off until my GTR arrived so I could see what else needs to be done and prioritise. but I did say I was in and there is nothing worse than someone who wants in the pussies out. So i'm in for the soarer. I'll email you shortly.

Thanks again for the effort mate.

Richard

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Hendasto
      Lets play a game - What is causing my oil consumption?

      By Hendasto · Posted

      Hopefully it ends up being something manageable, like a hone, rather than a full bore—it would be a huge relief if it’s not as bad as it looks. Hang in there; these setbacks are annoying, but it sounds like you’re handling it as smartly as possible.
    • Hendasto
      Are RBs worth building reliability wise

      By Hendasto · Posted

      At the end of the day, it’s all about understanding the odds and being comfortable with the potential cost, whether it’s horsepower on a build or chips on a roulette table. And I have to say, the Laine example made me laugh—some people really do embrace that carefree, “roll and see” attitude!
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks MBS206, i got that PDF but got abit overhelm with all the connections and tracing of wires. I wasn't expecting to plug the dash harness anywhere. i was just going to use my electronics jumper wires to plug into the right pins like ECU power, ecu ground, ignition trigger etc... I do have a few ratchet straps locking it down tight. Fire extinguisher ready and only a small amount of fuel at a time, enough to submerge the pump.
    • Songo
      New kid on the block

      By Songo · Posted

      Thanks GTSBoy, i will do abit more digging. I am missing a blue relay near the ECU connector... so i will chase that up in the next few days as well  
    • MBS206
      New kid on the block

      By MBS206 · Posted

      https://yariksteel.ru/manual/R33/Skyline_R33_elektroprovodka.pdf   Page 18 should be what you want for the Dash Cluster wiring. Though, you don't need the dash plugged in to get the motor running. What you want is power as how GTSBoy said. You need to power the ECU. Find in the above link the ECU pin outs (Verify them before just connecting them up from things written on the internet). Find anything needing power, give it power, find anything needing ground, give it ground. Then give the starter motor power through a big cable, and bridge the solenoid on the starter straight to power too.  ECU will be on, and when you give the starter power, it'll spin the starter motor, and it should start. I also hope you have a proper stand, and not just the engine sitting on some wood. You will want it bolted down properly.
×
×
  • Create New...