Jump to content
SAU Community

Recommended Posts

Need to sell my car: this car has made 540Hp over 400 KW on 18psi

The car is Black in colour with Red leather interior 2 recaro bucket seats, Sports steering wheels with lap timer, Apexi Rev/speed meter, Sound System with Kenwood 7" DVD player with TV recievers Eboost Gauge and 2 autometer gauges in a dual gauge holder mounted on the pillar.

Performance

RB30 Bottem End, Wiseco forged pistons, Gabbless Rings, steel rods, arp bolts all round, O ringed, and reciever groved ceramic coated chambers and pistons, Nismo Racing Oil pump, Nismo Water pump , Head has been ported with HKS Steel Values and Springs, GTR style head, Copper head gasket, Tomei Stage 2 Cams and gears, This engine was built 1000kms ago with paper work and warranty Built to handle 700Hp + @flywheel

Turbo: T66 Garrett 900HP Turbo dual ball bearing rollers, external Tial wastegate with Stainless steel manifold. Large Front mounted intercooler with Blitz blow of Value. 3inch Stainless Steel exhaust system.

Fuel System : 950cc SARD injectors Malpasi Fuel Reg, Bosch 044 fuel pump with surge tank GTR in tank pump working as Lift pump.

Ignition: M & W ignition pack, external coil pack 10mm custom made Spark plug leads.

ECU : Microtech LTX12 computer requires a 3 bar Map senor to run more than 18psi.

Microtech Dash

Exterior: 400R side skirts and rear bar , Drift wing (flat boot)

Tyres 20” x 8.5 Front 20” x 10.5 rear Kaokic rims

Brakes: Cross Drilled and slotted brakes all round.

Suspension : Tein HA adjustable suspension

$35000

Link to comment
https://www.sau.com.au/forums/topic/59778-r33-s2-1996-400kw-on-18psi/
Share on other sites

  • 4 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • neither stumble or cut really seem to be an appropriate term....hard to explain its like a rev limiter but at 4k, but it violently shakes engine and entire vehicle as the rpms will not rise over 4k, even with slow acceleration. as soon as it hits 4k, it sounds like entire spark is lost entirely. plugs were 1.1 which I used as such, but later put in new plugs gapped down to .8 changed back after issue arose when I replaced the coils, still does it with either plug gap...damn and it was all running so good.
    • Oh how times have changed! I actually lean it out relative to my water/methanol injector duty cycle. The methanol adds a lot of fueling and you can then lean it out even more due to reduced knock. 
    • Yeah my thoughts are the same, a well thought out WMI setup, would be slightly ahead of just straight E85 and you're also chemically intercooling the charged air, dropping it even further. This is why you need to add so much more fuel as soon as you spray. I remember someone taking me through their set up before (Dennis, has a R33, lives around Cabramatta - no idea if he's still around on this forum). He would target AFR 10:1 on 98, then as WMI ramped on, AFR would lean back up to 11:1. Amazingly, he did this all through his PowerFC, a relay to cut power to his EBC solenoid if there was not enough line pressure on his WMI kit. And of course, if there wasn't any boost made above gate pressure, you wouldn't be accessing the load cells with heaps of timing for WMI. One downside to that rudimentary setup, once the WMI came on, the EBC would unleash the dragon, and of course all the timing. Tyres would fry lol.
    • Shimmed or shimless, still solid, no hydraulic pump up stuff.
    • They have said food will be limited. Mainly meat pies and sausage rolls from memory. But they have a coffee van!
×
×
  • Create New...