Jump to content
SAU Community

Help, Flywheel!??

SkyGTRline

By SkyGTRline,
in Australian Capital Territory

 Share

Recommended Posts

SkyGTRline Mentor

SkyGTRline

Posted
Posted

hi all,

ATM just changin clutch over on the line.

Trying to get flywheel off...

Tried cracking while 2nd person holdes front pulley.... Front pulley un does.

Tried a shit rattle gun with shit compressor..... Not guts..

Tried sticking a cro-bar onto teeth of flywheel and cracking... but as the car is about 1foot of the ground... 2nd person slides away....

How can i get this damn flywheel off... wanted to get off now so the misses can take in to get machined tomorrow, and i can finish it when i get home from work....

all help appreciated.

Limited tools.

Link to comment
https://www.sau.com.au/forums/topic/60394-help-flywheel/
Share on other sites
sky30 Mentor

sky30

Posted
Posted

Get a Short peice(around 200-300mm) of chain, or rope, and bolt one end to the flywheel in the existing clutch bolt holes, then bolt the other end to one of the gearbox mount holes on the edge of the block. Now the flywheel can only turn as far as the chain will let it. You can use the same method to tighten them.

Another method is to use a large screwdriver to hold the teeth on the flywheel, put the screwdriver through the starter motor hole and wedge it between 2 teeth, and the base of the starter motor hole.

Good luck

Link to comment
https://www.sau.com.au/forums/topic/60394-help-flywheel/#findComment-1146679
Share on other sites
Jay95R33 Grand Master

Jay95R33

Posted
Posted

Best way I have found is to get a big allen key (the ones that are 3-4 inches long, then turn 90 degrees and have a further 1-2 inches), slot it into a bolt hole and turn it so it locks it against the flywheel teeth. That will stop the flywheel from turning while you get a loooong extension bar onto the bolts.

J

Link to comment
https://www.sau.com.au/forums/topic/60394-help-flywheel/#findComment-1146710
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • GTSBoy
      RB26DETT Sketchy boost mod?

      By GTSBoy · Posted

      There's restrictor pills in the stock boost control hoses. That's how they set the amount that was bled off and hence the "high" boost setting. The usual mod in the day was to remove it and send the "high" boost setting up to about 14 psi.
    • ARB26
      RB26DETT Sketchy boost mod?

      By ARB26 · Posted

      Thanks Duncan, that's the best info I've read. Furthermore after learning about the PCM programming side controlling the factory boost solenoid, the purpose of the solenoid is to "bleed" boost when pin 25 is earthed, thus allowing spring pressure in the wastegate actuator to overcome diaphragm boost pressure, thus closing or reducing the position of the wastegate flap creating more boost as the turbo is able to spin faster. It's pretty cool to see a designated Pill to do exactly this, would have liked to have seen it with a tiny filter over the end for those moments in vacuum.  The constant bleed pill has now been removed completely from the system and solenoid boost control has been restored once again.   Case closed 😂
    • GTSBoy
      Cas issue

      By GTSBoy · Posted

      The wideband reading is meaningless if it's not running. Why are you using shitty old sidefeeds on any engine, let alone a Neo? What manifold and fuel rail are you using to achieve that? Beyond that, can't help you with AEM stuff as I've never been their ECU/CAS combo.
    • Duncan
      RB26DETT Sketchy boost mod?

      By Duncan · Posted

      Manual boost controllers (where a little of the boost was bled off) were quite common back in the day, because they were cheap and easy. Generally they had a manual adjustment screw rather than being fixed like yours. Down side is they always bleed boost, not just when you want them to so an electronic boost controller that uses a solenoid will have less lag.
    • nash47
      Cas issue

      By nash47 · Posted

      Hello , im new here and i have A31 home build  RB25det neo stock eng / turbo  aem ems 2 blue connector  aem 3.5 map aem cas disk aem wideband connected to ecu  355 lph pump 550 nismo yellow injectors side feed aftermarket regulator  and won’t start with base aem tuner basic tune eventually flipped cas 180 degree so it triggers on correct stroke not in exhaust cycle  Now it won’t start Wideband reads 10 and 11 at lowest fuel setting  and will share calibrations soon for aem tuner i think something is wrong in aem tuner    please if you have any information, am very grateful         
×
×
  • Create New...