Jump to content
SAU Community

R32 idle speed adjustment

B0oStEr

By B0oStEr,
in General Maintenance

 Share

Recommended Posts

B0oStEr Mentor

B0oStEr

Posted
Posted

My R32 used to idle way too fast (1500-1700 rpm) for 10 or so seconds after I pulled up at the lights or what ever, before it dropped to 800rpm.

My mechanic adjusted the idle control device at the rear of the inlet manifold by disconnecting the plug then screwing the adjustment in until it was right then he reconnected the plug. Apparently it was way out.

It's been much better since he did this.

My sons recently purchased R32 has a similar fast idle problem and I said to myself "I know this one" and pulled the plug off the controller and tried to screw in the adjustment. The only problem is that it's already screwed in all the way (1200 rpm idle) and screwing it out only increases the idle so there must be another problem.

Does anyone have any ideas what it could be or how i should adjust the idle properly?

Link to comment
https://www.sau.com.au/forums/topic/61185-r32-idle-speed-adjustment/
Share on other sites
Godzilla32 Veteran

Godzilla32

Posted
Posted

I have the same problem but its not my AAC vavle it can be an intake leak. Around the plenum or throttles, use sum aerostart . Spray it around the intake and throttles. if the engine picks up revs then you got a leak there

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • funkymonkey
      Howdy Y'all

      By funkymonkey · Posted

      Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Dose Pipe Sutututu
      Starting again

      By Dose Pipe Sutututu · Posted

      Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • R33_Guy
      Speed Sensor replacement

      By R33_Guy · Posted

      Thank you so much for the help
    • GTSBoy
      Speed Sensor replacement

      By GTSBoy · Posted

      Yes it is ATF. I quote @Duncan "it takes a good synthentic auto trans fluid like Castrol Transmax Z" It's not a diff. It's a transfer case. Totally different thing. Yes, fluid will come out the sender hole. No you do not really need to drain it. Just pull the old, quickly poke the new, clean up and top up. But realistically, you should probably take the opportunity to change it anyway.
×
×
  • Create New...