Jump to content
SAU Community

Recommended Posts

how hard is it to remove the wheel and airbag? and is it possible, say, to replace the standard wheel for track days them put it back on when you drive off? or would this be too stupid/hard?

Its fine to replace the standard wheel with an aftermarket one.

But you couldnt replace the passenger side airbag with anything, unless you just disconnected the fuses :(

  • 2 weeks later...

Its not hard to remove the airbag steering wheel... if you really don't like it, just change it to one you want, but keep the orig incase you get defected for it. takes 10-15mins to change the steering wheel

ive seen a supposed series 2 with only drivers side airbag... i dont trust the dealer so i reckon it was a bit of a mock up series 2

btw i have seen late 94's with driver side airbags

my series 2 has both airbags but no abs

Its not hard to remove the airbag steering wheel... if you really don't like it, just change it to one you want, but keep the orig incase you get defected for it. takes 10-15mins to change the steering wheel

if you do remove or disconnect any airbags you will receive an airbag code....u wont be able to extinguish this until the system is operational......to get rid of the code switch the ign on and pump the door pin switch 7 or more times withing 10 seconds of turning the ign on

if you do remove or disconnect any airbags you will receive an airbag code....u wont be able to extinguish this until the system is operational......to get rid of the code switch the ign on and pump the door pin switch 7 or more times withing 10 seconds of turning the ign on

An airbag code? I've removed my airbag and steering wheel twice, and put it back on twice and never had any problems - the airbag light doesn't come on (except for when starting the car as per normal).... I was told that if you remove the airbag Nissan need to reset something but i've never had any troubles - of course i've never had any reason for my airbag to go off...

Where is this airbag code?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Depending on how long the car sat it is very possible for injectors to be stuck open or closed, I'd get them cleaned and flow tested. Other than that, obviously when the loom changes and the car doesn't start any more....the loom is suspect so some tracing / comparing may be required
    • Harness is for a s1 Rb25det, and it is engine and lower harness.  the old harness had broken off plugs and was in very rough condition/exposed wires and splices etc. it is not able to be put back on the car, I could visually inspect to see if they had rewired any pins on the ecu plug. The fuel pump definitly isn’t turning off it’s an external pump and very loud you can hear it. Will look at the other harness tonight, am also going to pull the fuel rail and watch the injectors spray, will update here with what I find. Pretty sure at this point it has to be something to do with injectors because car will fire up on starting fluid and cas is clicking the Injectors. Fuel pressure is steady 43psi 
    • Check the injectors flow evenly, and are actually flowing what you and the ECU think they should be flowing. If it's starting up on starter fluid, you have a fuel issue. Is it possible under cranking your fuel pump is turning off?   The harness you replaced, is that the whole engine harness? Do yourself a test, and drop the old harness on and plug it into the Z32 ECU. It's possible they've wired things different. From memory S1 to S2 is different in RB25 and you may have a wrong loom
    • I haven’t pulled the injectors to watch them spray yet but they are clicking from the cas and all of the spark plugs are wet with fuel. I’ve thought the cylinders were being flooded from the beginning and was hoping fuel pressure would fix it. Tonight I am going to pull the rail and watch the injectors spray. Don’t know how to test/diagnose if the plugs are firing in correct sequence but that should be a timing thing and as far as timing goes my car still has the half moon for the cas can only install it 1 way. And my mechanical timing is 100% correct I posted photos above. Confirmed with the balancer on and off. 
×
×
  • Create New...