Jump to content
SAU Community

Plug Gapping and Misfiring

adam 32

By adam 32,
in Engines & Forced Induction

 Share

Recommended Posts

adam 32 Grand Master

adam 32

Posted
Posted

i was gettin a misfire on high boost before, so i put in new plugs gapped to 0.76mm (damn non-metric feeler guages:D )

anyway, now it pulls hard all the way to redline on 1bar boost, but it seems to misfire at idle?! (sounds like ive got cams!) is this because im now running too small a gap? or is this what you sacrifice in order to get a reliable spark under high boost?

thanks

adam

Link to comment
https://www.sau.com.au/forums/topic/6160-plug-gapping-and-misfiring/
Share on other sites
rev210 Grand Master

rev210

Posted
Posted

Could be the smaller gap and worse still if you have installed a colder heat range of plug.

The smaller gap/colder plug provides better combustion for top end (as per the reason you did it) but, provides poor combustion at idle. The plugs will have less life in them as well.

Best thing to do is practise changing plugs, so you can change to a colder set for race use and leave a nice warm setting for the street. Poor combustion also shortens the life of the engine BTW.

adam 32 Grand Master

adam 32

Posted
  • Author
Posted

but theres only poor combustion @ idle so should be sweet:P

i dont fancy changing plugs THAT often, took me long enoug thanks to nissan's coil packs :) the plug is 1 heat range colder, so thats gunah add to it as well.

i guess im sacrificing the bottom end for top end, as it seems to go with turbo cars when they make big power.

rev210 Grand Master

rev210

Posted
Posted

The plugs foul at idle, and get cleaned up when you floor it.

They just won't last as long as your old ones. Why not run the gap at 0.9 or so, with a colder range plug I'm sure you won't be down any power and it will give back the idle perhaps.

Zahos Mentor

Zahos

Posted
Posted
0.9 on a colder plug should be fine.

Nope! I've tried numerous combinations with heat range and gap, and what I'd recomend for street use is a heat rating of 6, and a gap smaller than 0.8mm. If you have an aftermarket ECU, or a SAFC, then this recomendation doesn't really apply to you...

With stock ECU, b/c the mixtures can get really rich, you need a warmer plug that can burn some of the carbon deposits off the plug. The colder plug will not last long, as it will get fouled very quickly (a couple of weeks), and will need to be pulled out to be cleaned. A warmer plug will go a lot longer before it needs a clean.

As for gap, I've tried

0.9 with a colder (7) plug, 0.8 and 0.7 as well. I found the smaller gap to be the best....

But like I initially said, a warmer plug and smaller gap is best for street use..

I'd say NGK BCPR6E (NO S). This has a heat rating of 6, and the v groove. Gap this anywhere between 0.65 and 0.75, and your Line will run much better (remember, only if you nave stock ECU meaning rich mixtures). At this configuration the 5000rpm misfire on the R33 happens much less!

I only see it when I have been driving the car for more than 30 mins... weird!

Zahos

JH32 Grand Master

JH32

Posted
Posted
Originally posted by Zahos

But like I initially said, a warmer plug and smaller gap is best for street use..

I'd say NGK BCPR6E (NO S). This has a heat rating of 6, and the v groove. Gap this anywhere between 0.65 and 0.75, and your Line will run much better (remember, only if you nave stock ECU meaning rich mixtures).Zahos

Zahos ... does this apply to R32s as well??

Zahos Mentor

Zahos

Posted
Posted

OK then, well I guess the same theory applies to R32's as well. But no matter what, if u have stock management, and higher boost, you will see this problem. What I suggested merely deminishes the magnitude of the problem, and will prolong it from creeping up. I have had my plugs in for 2 months now, and I dont see the problem very often (running 0.7 bar ~10psi).

rev210 Grand Master

rev210

Posted
Posted
Originally posted by Zahos

Nope! I've tried numerous combinations with heat range and gap, and what I'd recomend for street use is a heat rating of 6, and a gap smaller than 0.8mm. If you have an aftermarket ECU, or a SAFC, then this recomendation doesn't really apply to you...

As for gap, I've tried

0.9 with a colder (7) plug, 0.8 and 0.7 as well. I found the smaller gap to be the best....

But like I initially said, a warmer plug and smaller gap is best for street use..

I'd say NGK BCPR6E (NO S). This has a heat rating of 6, and the v groove. Gap this anywhere between 0.65 and 0.75, and your Line will run much better (remember, only if you nave stock ECU meaning rich mixtures). At this configuration the 5000rpm misfire on the R33 happens much less!

I only see it when I have been driving the car for more than 30 mins... weird!

Zahos

Adam's got an HKS AFC thingo.

Like you I run the stock rated 'warm' plug. Regardless of gap they (warm plugs) will have a nicely cooked electrode in no time with a setup like Adams with revs and tO4 style boost.

adam 32 Grand Master

adam 32

Posted
  • Author
Posted

the problem doesnt seem to be as bad anymore actually. im not sure why...

even if it didnt rectify itself i was happy to run a 0.75mm plug gap as it pulls very nicely through top end

jimi if ur running the VG30 at that sorta boost (which u should :D) then run the same plugs as me. i think theyre BKPR6ES or something

Black33 Proficient

Black33

Posted
Posted

what gap do u guys think I should run:

I have -

full exhaust (dump, front and rear)

10 - 11psi boost

pod

cold air intake

Also, how long does it take to remove all of the stuff under the plastic panel on the engine head to get to the plugs? is it hard (i got to it and then stopped)?

thanks

Zahos Mentor

Zahos

Posted
Posted

Try 0.7 or even 0.65+

A good spark plug (copper) is NGK BCPR6E

Platimuns r good, but not worth the money, as the only benefit they have is a longer life span. I dont plan to leave plugs in there that long anyhow, as they foul easy when running rich....

R32 Zilla Community Regular

R32 Zilla

Posted
Posted

I have the same problem with my r32

Running 19 psi through a hks gt2535 and a rechipped computer it misses at about 5000 rpm.

Have tried lots of different things to fix it with no luck yet.

Iam now running a gap of .65 and when i did this it developed a miss at idle (like adam32) . This does not worry me as all i want is for it to rev cleanly to redline.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • MBS206
      R32 GTST - 600KW+ RB28/CD009 Build

      By MBS206 · Posted

      Slow when hot could also be because its getting more dynamic compression, OR things are getting a bit tighter once it is all expanded. If it were an earthing issue, typically I'd expect you to have it have issues all the time. Unless it's really a combination of both things. Where the higher compression, and things being a bit tighter, is giving that bit of extra load and you do need a slight clean up on the cables/connections.
    • dbm7
      Stagea Front CV Axle Question

      By dbm7 · Posted

      Yeah, this is one of the most annoying things about nissan part numbers... I've got an unrelated example... Image is of the AT output shaft ~ they have the same part#, but clearly the shaft on the left is beefier design to that on the right ...the difference (essentially) is the 'lighter' shaft on the right, is for engines up to RB25DE (this includes RB20 variants) : the shaft on the left is for RB25/26DET(T)....are they interchangeable? Yes...but obviously one shaft is going to be stronger than the other...and, the lighter shaft is around USD115, but the heavier shaft closer to USD150...same part#... ...epc-data usually tells a tale ~ the amayama listing for 39100-23U60 has a note "Longest side is between 60 and 105 cm" ; no such info is there for 39100-23U70 ...and given the great disparity in price between the 2 parts, it makes me at least curious (to the point of caution) where the 'extra money' went? ...ie; these 2 parts have a cost difference that (to myself at least) isn't explained by 'plastic boot'...ie; with amayama there's AUD700 price difference ...plastic versus rubber?...I'm not seeing it like that...and 60cm ~ 105cm...??...that's a huge disparity....something hinky going on here... I'd try searching by VIN, not model... /2cents
    • Duncan
      Stagea Front CV Axle Question

      By Duncan · Posted

      I don't know for sure, but I'd expect them all to be interchangeable given the diff end and hub end don't move/change between any C34 series. Often Nissan will change part numbers and the aftermarket follows those year ranges; but the original part number change doesn't mean other parts won't fit. The change could be a change in material, internal parts or even just supplier. For example, all the RB gearbox to engine bolts are no longer available and there is a new part number instead. The only change is they went from cadmium plated bolts to zinc plated due to the issues manufacturing with Cadmium. They look different but work the same.
    • soviet_merlin
      Stagea Front CV Axle Question

      By soviet_merlin · Posted

      One year is a bit concerning. Did you try contacting GSP? It says 5 year warranty on the box if I remember correctly. I'm also running their driveshafts on my S2 Stagea.   You could check the part numbers on Amayama for your year. Here's the link for my 1998 which gives the 39100-23U60 part number. Well, that and 39100-23U70. https://www.amayama.com/en/genuine-catalogs/epc/nissan-japan/stagea/wgnc34/6649-rb25det/trans/391 What does it say for yours?
    • S1_C34
      Stagea Front CV Axle Question

      By S1_C34 · Posted

      I ordered a GSP Front R/H Axle from here - https://justjap.com/products/gsp-premium-front-driveshaft-r-h-nissan-r32-r33-r34-skyline-gtr-stagea-4wd#description It lasted around a year before one of the boots blew out. I'm lowered, but I have GKTech roll center adjusters. One year seems a little premature. I think I'm going to spend the extra money on an OEM cv axle this time. This website - https://tfaspeed.com/collections/nissan-stagea-wgnc34-x-four-parts/products/nissan-stagea-awc34-260rs-rb26-right-front-axle-drive-assembly Makes it sound like the readily available OEM CV axle will only fit 11.1999 Stagea and up (mine is a 2.1997 S1). The JustJap listing didn't mention any years or anything for the GSP axle. Amayama shows '11.1999' and up as well for that part number. As well as 'plastic boot type'. See attached picture. So I guess my question is, does that axle (39100-23U60) really only fit S2 Stagea? It's the front driver side. If it does, I'd love to buy that instead of rolling the dice on another GSP. I've found that OEM one cheaper here: https://www.partsfornissans.com/oem-parts/nismo-jdm-r32-r33-r34-skyline-gtr-r32-gts4-right-front-axle-3910023u60 and here https://www.nissanparts.cc/oem-parts/nismo-shaft-ft-drive-3910023u60 Just a little confused because the JapSpeed listing for the GSP front driver axle doesn't mention any specific years or anything and it fit my S1 Stagea fine. So will 39100-23U60 fit my S1 Stagea even though technically it says '11.1999' and up? What would have changed? Thanks.  
×
×
  • Create New...