Jump to content
SAU Community

Recommended Posts

Hi all,

Quick question regarding the Power FC boost control kit...

I've just bought the kit that was previously on an sr20 which has a factory boost solenoid..

Now I want to install the kit onto an rb20. The Apexi Solenoid has a positive and negative wires which I need to run to the power fc, the only thing is I'm not sure where to...

I believe it goes to the plug next to the hand controller as there are 5 wire slots available and three go to the boost reader(Sensor)...

IE...

SOLENOID PRESSURE SENSOR

FREE FREE BLACK GREEN RED

Can someone tell me, who's using a power fc that didn't have a factory solenoid where the aftermarket solenoid goes to...

IE...

SOLENOID PRESSURE SENSOR

GROUND POSITIVE BLACK GREEN RED WIRES...

Thanks in advance for any help you can give me :P

Cheers

Dan

Link to comment
https://www.sau.com.au/forums/topic/62949-power-fc-boost-control-kit/
Share on other sites

i think i am after the same info

but not sure

I currently have a PowerFC in my RB20... but using a Greddy boost controller.

I have a mate who has the boost solenoid from an AVCR which i hear is exactly the same as the one from the PowerFC Boost Control Kit, and i want to connect it up to my FC..

But it only has wires coming off the solenoid. with no plug. so i need to find out where the wires from the solenoid connect onto the PowerFC. like the exact pins..

Cheers :(

I have an SR20 so hopefully is similar. The 2 wires from the apexi solenoid need to be connected to the wiring for your FACTORY solenoid (as PFC uses the stock wiring loom to adjust it, the factory solenoid is then redundant).

The apexi pressure sensor then plugs directly into the PFC unit (next to the HC plug).

There are 2 "versions" of PFC, each uses different boost kit (the wiring from the sensor is different), older version has 3 pins/wires, newer version 5 pins/wires.

Hope that helps.

The RB20 Power FC wasn't really designed for use with the Boost Control Kit, but you can use it. The RB20 (R32 GTST) PFC is basically the same as the R32 GTR PFC, but AP Enginnering modified it to work on the RB20. That is why it still has inlet temperature correction (like an R32 GTR) even though RB20 's don't have an inlet temp sensor.

Enough history, how do you connect it....

RB20's have a standard map sensor, so you don't have to connect up the one that comes with the Boost Control Kit.

If you look at the pin outs on the standard R32 GTR ECU, you can see the wires for the standard boost control solenoid. The pin out is basically the same on the R32 GTST, there is just no wires for the boost control solenoid becuase R32 GTST's don't have them. That is where the Boost Control Kit is wired into the Power FC.

Hope that is of some help.:cheers:

Thanks heaps for the replys :P

The sr20 boost kit has a plug for 5wires that fits into the FC, ie next to where the hand controller fits, however the FC for the Rb requires a plug for 3 wires... So thats definetly where the Map sensor would be wired to...

As for the solenoid, thanks heaps sydneykid :(

  • 1 month later...

I have all the pinouts and wiring diagrams for the RB20DET, but having trouble finding a pinout diagram for the RB26DETT. Anyone able to help me with a site or a copy.

Also have an air temp sensor here that im hooking up to the PFc, so need to know which pins are for the boost control solenoid and air temp sensor?

Thanks ppl:thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Seat of the pants assessment of the new intake: The car is way less "doughy" when hitting the loud pedal, especially off idle when stopped or in traffic, I did use a cheapo lazer thermal thingo to measure the temp around where the pod filter got its air, it was between 55 - 60°C, in saying this the car was shut off and not moving, so the OEM intake pipe was not supplying any fresh air to where the pod was when the car was at least moving A weird bonus was induction noise on the throttle in the cabin increased a bit,  I was worried that I was actually going to lose some of that induction noise I love so much, outside though, when I got the daughter to do a WOT drive by pass for me, the induction noise has increased alot when on the throttle, not quite ITB doort, but well up there I'm extremely happy with the results and have been exploring the country roads in the region  As for house mods: 1.New front fence is up and is awesome, it really upgraded how the joint looks from the street, and the added security is nice 2. Electricians have replace some interior lights, and with more lighting in the garage, a few new motion detecting lights out the front above the garage, front room, and at the front door, which I have already found heaps helpful coming and going, also now has fancy pants CCTV all round the house The only hold point for power though is the solar and batteries due to supply issues, although this will happen over the next few weeks 3. I have done a heap of landscaping out the front and I'm almost ready to do a new small retaining wall with some nice blocks to replace the brick and cemented in rocks around the raised garden beds cemented in river stone "was the fashion at the time" the house was built. I currently have a pallet of retaining wall blocks and 2 bulka bags of 20mm blue metal to replace the wood chip that is in the raised garden beds around the house 4. I now have 3 big raised garden beds for out the back to grow some vegetables, about 70cm high, 200cm long and 100cm wide 5. My 2 compost bins are already pretty full with brown, green and kitchen waste from the landscaping I'vedone so far, but they will probably take a few months to break down, so anything else that gets chopped, trimmed, and kitchen waste will just start filling the base of the raised garden beds to about 30cm before I start throwing 40cm of good compost, and stuff, for the vegetables to grow in, I'll need a few ton of compost and soil, but the local supplier can sent me bulka bags of the stuff Basically the logs, wood chips and a few strategically placed rocks for drainage, will give the beds some good organic materials down low to break down over time, and they will hold moisture during the warmer months to save the water in my big arse water tank if we don't get alot of rain So, all in all, the car and house mods are going well, and I'm really enjoying being retired, I sleep in too 0700 and slowly plod around inside until I feel like actually doing anything, and only work in the yard for as long as want, which has actually been alot over the last few weeks,  although when you look at it, it seems that not a huge amount of work has been done,  until I look at the before I started the work pics Happy days and good times indeed 
    • hahaha yeah. Plan is to get side skirts and probably just rear pods. But going to do them one-by-one. I've got a set that I really like from RHDJapen, but that one isn't shipped to AU. So need to find someone who can get it for me
    • Here's an idea, answer the questions I asked you as they are trying to work out WHY the LSD will be binding up in a straight line.
    • You haven't driven many modern cars then have you? Most of them have sfa steering feel with their stupid electric bullshit steering systems.
×
×
  • Create New...