Jump to content
SAU Community

Recommended Posts

Well said, Merli.

Kabab, if only WSID would do this. Maybe they could trial it once a month, but there also needs to be a demand for it. I personally think that the govt has the responsibility to push/promote this in conjunction with the police and WSID. I know that Fairfield Regional Command had a WRX donated to them for this purpose (Wed Off-Street meets), but I have not seen this car since that time. It's the govt's reponsibilty to counteract the problem not just with negative measures like raod blitzes, but also by doing something positive, like assisting in the promotion of off-street meets. it shouldn't be left up to the private sector to undertake this (like Subaru's WRX donation to the police!). Pull your finger out Mr Carr.

  • Replies 124
  • Created
  • Last Reply

Top Posters In This Topic

I know that Fairfield Regional Command had a WRX donated to them for this purpose (Wed Off-Street meets), but I have not seen this car since that time.

It's been there a few times when I've been there - too bad they Highway guys cannot drive in a straight line to save themselves. 15's?!?!? WTF?!?!?

Adrian

actually, i can say i have a clear conscience when it comes to things. I wasn't picking on him for doing it, im just saying, why are the ordinary 'line drivers being bashed in the news, when that dude posts videos of it on his site and yet not a word is said? Afterall, he is meant to be a prominent figure in the skyline community, building the world's 3rd fastest (correct me if im wrong) GT-R and 4WD/AWD, building it locally too.

I'm not saying we are all perfect, god knows im not.

If you DO do something stupid on the streets (and you shouldn't, but if you chose to), atleast make sure it's completely dead =/, unlike the one's at exvitermini, you see: him taking off behind a taxi on a highway, him launching it at the lights (at sylvania i think it was) with a celica along side him, and his car looking a tad "swirvy" too. Then there's 8TH-SIN: Fishtailing it on a street where there are parked cars on either side, and spectators amongst those cars. Now, a powerful RWD car fishtailing it in that situation, kinda dangerous don't you think?

Also, the 8TH-karma video. Tearing the strips of freshly painted road markings right infront of the workers who just did them. Gives us imports enthusiasts a bad name, don't you think?

Seeing at the time there was no real place they could do all this safely, couldn't they atleast chose a place where there was a minimal risk to by-standers, themselves and other cars? (one of the GTR-700 videos was in a situation like that though, looked dead as etc).

Anyway, i'm not bashing him for doing it, he loved his car, wanted to have a bit of fun with it, as we all do.

I'm just saying that he is getting off scott free when there is evidence of him doing it, and yet the rest of the community gets slammed. But anyway, that's in the past now, and i don't feel like going on and on in the one post.

btw, i think people are getting a little confused and influenced with the japanese scene and RH9. I don't think you see them racing on public roads with other cars around (one's who aren't taking any part in it what so ever).

Sure, some tuning workshops do their tuning runs on public roads etc, but most of them are in the dead of night when the roads are pretty much, well, dead.

I think it also comes down to people's "over confidence". Them thinking they are excellent drivers, when infact, they are not. There was something about this a few years ago on telly, on a current affair, or today tonight, or something. They took a bunch of blokes in hotted up cars, one was a supposed 500kw R32 GT-R, maroon in colour (or wine red), another was an S14 i think. They all rated themselves at excellent drivers, noone gave themselves below 7/10. Anyway, as you could imagine, they all failed miserably, in their own cars.

Maybe, this is a maybe ofcoarse, the government could subsedise the costs of advanced driver training courses for car enthusiasts and those who wish to drive around in high powered vehicles, to try and make the roads safer for themselves and others? I mean, you can't expect an ordinary joe bloe to sit down in a 500kw car and drive it around like he is peter brock or tetsuya kawasaki.

Newho, enough of my ramblings for one post.

BTW, HOW BOUT SOME GOVERNMENT FUNDING TO KEEP WSID OPEN 7 DAYS A WEEK? :D

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...