Jump to content
SAU Community

Recommended Posts

1 x Intercooler AU$250

1 x Blue Pipes AU$300

1x Red Pipes AU$300

Key features:

High flow High power handle supported upto 700hp

Big inlet 76mm or 3"

High efficiency big core with internal fins!!

Low pressure drop 0.2psi at 15psi 80 psi tested

Dimensions Details:

Core Length : 24" (600mm)

Core Height: 12" (300mm)

Core Thickness: 3" (76mm)

Inlet Size: 3" o/d (76mm)

Outlet Size: 3" o/d (76mm)

"End to End" Length: 32" (800mm)

Heat Exchange: 72C - 24C

:

Contact - [email protected]

IMGP0336.JPG

blue.JPG

red.JPG

so practically i can get a FMIC kit from you under $600 ? this is for realz?

Yes, you are right. Under $600 you get intercooler + piping.

just let me know what colour you like

The kit does not include the clamps, brackets and siliconhose.

I hope this helps, turbokit

size of piping, let me guess 3 inch? Also do the fan blades need to be shaved?

High flow High power handle supported upto 700hp

Big inlet 76mm or 3"

High efficiency big core with internal fins!!

Low pressure drop 0.2psi at 15psi 80 psi tested

Dimensions Details:

Core Length : 24" (600mm)

Core Height: 12" (300mm)

Core Thickness: 3" (76mm)

Inlet Size: 3" o/d (76mm)

Outlet Size: 3" o/d (76mm)

"End to End" Length: 32" (800mm)

Heat Exchange: 72C - 24C

Youve only given the size of the intercooler and not the size of the piping. My guess is that it is the same light weight alluminium piping that is going around which is 2.5 ". So youll need silicone reducers to fit to the actual cooler. Are you in Sydney?

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
    • Yes sir am asking is there possible way from aem tuner from wiring pins 
    • Have you checked cam to crank timing and confirmed balancer marks are correct?
×
×
  • Create New...