Jump to content
SAU Community

Recommended Posts

Looking at doing some sort of heat shielding for my 2 pods that are just sitting there sucking hot air at the moment but wondering what to do about getting some cold air into them afterwards.

My gtst was easy as it already had a nice 3" hole from factory right where I wanted it.

My question is it safe to cut a 3" or so hole right below were the pods are then I could do the induction easily, just ive heard something about how it makes all the support weaker on that side etc etc. It probably wont be so obvious just looking at it from the engine bay.

Only other option I can think of is the headlight replacement but I want it for street use so that would be no good.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/
Share on other sites

It has the stock airbox, but who knows what in it or if the box is modified?

LW.

OK I'll go another route.

Stock air box, Piper cross panel filter, custom stainless pipe to replace stock rubber one between turbo/s and AFM.

maybe ask Sydney Kid the max power he has seen from that set up on a GTR.

Honestly, when I had my GTST (R32) and had a pod filter, the thing was only producing like 155rwkw and the engine bay was so hot, the intake temps were like in the 60's during sydney traffic.

so imagine the engine bay of a gtr with 2 turbo's producing obviously more power.

and 2 pods taking up the same room.

even hotter air there for sure.

the stock air box is good.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1222333
Share on other sites

GTST: I am aware of Gary's view on Pipercross filters: in fact I will be putting one in the (stock) airbox of my R32 GT-R very shortly.

My point was more that although the Mines R34 may have the "stock airbox", for all we know its been completely changed on the inside. I'm not sure it makes a particularly good point of comparison given all the unknowns surrounding the car.

LW.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1222395
Share on other sites

LW - I was just trying to make the point of the stock GTR air box with a panel filter is going to be a better option that PODS in the engine bay.

AND it is cheaper to buy a stock air box and new panel filter, than it is to buy an aftermarket heat shield/air box which probably still uses tha factory snorkel.. to shield off the dirty used pods that would have come with the car from japan.

you will be able to produce the same power (possibly more) if using stock turbo's and maybe even with after market turbo's..

the cost of buying a stock airbox and panel filter is going to be cheaper than buying a heat shield for sure. and give a better result.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1222437
Share on other sites

My question is it safe to cut a 3" or so hole right below were the pods are then I could do the induction easily, just ive heard something about how it makes all the support weaker on that side etc etc. It probably wont be so obvious just looking at it from the engine bay.

To answer your original question I drilled a 3" hole below my rear pod. I don't see how it has any effect on the structural integrity on that side. I have two 3" flexible hoses in the front bar. One running through the hole to my rear pod, the other through a factory whole under the headlight to my front pod.

Hope that helps.

Gary.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1224680
Share on other sites

theres a factory 3" hole under your front pod? ah thats right yours is 32 so probably different.

You reckon 1 3" hole would be enough for the 2 pods? dont really want to cut 2 holes. Might cut 1 hole and put a scoop intake on also (hope it doesnt look ricey :Oops: )

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1224876
Share on other sites

The factory hole is under my headlight and was used for part of the air box setup that went to a resonator box. I thought the 33's would have had it too but I could be wrong. It is more like a rectangle hole next to the carbon canister. One big hole is probably enough though.

Link to comment
https://www.sau.com.au/forums/topic/65156-cai-on-33gtr/#findComment-1225169
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Latest Posts

    • Per Mark Roberts of Sonictune: Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • Per Mark Roberts of Sonictune:     Mark Robert Author At this time, no. No ETA either 2016-17 models. You will be able to purchase and install a 2018.5+ TCU though   TCU purchasing and pricing info! As we near the release of TCU tuning, I am going to answer some questions I get asked often.   What do I need for TCU tuning? At this time, you will need a 2018.5+ TCU to be able to tune. If you have a 2016-to early 2018, you will need to replace your TCU with the newer version. One good way to know if your TCU is good is if you have auto upshift in manual mode in 1st gear around 6500 rpms. If your manual 1st gear goes to 7k rpm and will hit the rev limiter unless you shift, you have the older TCU.   Why do I need to buy another ecu license/phone flash if I already have it on my ECU tune? The TCU is its own computer module. It is completely separate from the ECU. Because of this, you will be required to purchase a TCU license and, if your tuner has it, the phone flash license required to tune it via phone/bluetooth.   Do I need TCU tuning? TCU tuning is NOT required. However, the faster your setup, the more it will assist in track and dragy time consistency.   If I’m ECU tuned by (tuner A) can I get my TCU tuned by (Tuner ? Yes, since it’s a different module and a completely separate flash, you can have two different tuners. However, it is highly recommend that you have both tuned by the same tuner. For me, my TCU tuning will directly complement my ECU tuning style and features and running my ECU and another TCU or vice versa MIGHT cause some issues. At this time and for the foreseeable future, I will only be tuning my current ECU tuned customers TCUs.     I have a SYVECS AWD controller. Do I still need it? Yes! The AWD controllers main job is to control your AWD system. However, with TCU tuning, you will no longer need the auto-shift function as that will be done through the TCU. The AWD controller will still be very beneficial for racers looking to maximize traction on the launch.     Shift schedule changes: holding gears longer at lower pedal input as well as max shift rpm changes. Please note, the new ECU race rom coming out will address 90% of the shitty drivability issues these cars have through custom maps from myself and Racebox—as well as others I am sure.   Increase shift speeds: as seen in the videos I’ve been posting, the TCU shifts much faster once tuned.   Increased shift pressures: as also seen in the videos, much firmer full throttle shifts.      
    • The fancy pants red shock tower brace is finally incoming from MX5 Mania, getting it shipped from 'Merica has been a long and problematic process, and GWR, the 'Merican supplier will not ship directly to consumers outside of the US, Mania basically had to order a heap of them, the colour choice was silver, or red, and we all know anything red adds 5 killerwasps of dynotorques..... Whilst it does fit over a 2.5, and I've seen a few photos and videos of it being installed and fitting, google also says it might get real close to the FAB9 intake front runner, people in the US says it does fit with the FAB9 intake, except for one person who said it slightly touched.......so there is that.....LOL..... As it seems that I am the first in AU to have this combination of parts there's no local knowledge about fitment, so I'm just a willing guinea pig in this endeavour, I'll cross my fingers and toes and hope for the best In other news, I ordered stuff from China  on the same day I ordered the 23° silicone bend from Victoria, the stuff from China arrived a day ago, the 23° silicone bend is still travelling around Australia thanks to Australia Post, and "may" be here next week
    • Very good news...I contacted Racebox about it last night. My car is a 2016 so remains to be seen if it is compatible, requires a TCU swap, or is impossible.
    • What ECU are you running? This is probably the biggest question. If it's a PowerFC, I'd probably change the ECU and get something newer that will handle the injectors in a nicer way.
×
×
  • Create New...