Jump to content
SAU Community

Recommended Posts

Hi,

Anyone know how to fix this problem?

I change gears fine. everything works.

There is this rattling noise that bothers me. I don't hear it when cruising along with the exhaust and radio going. But, while idling in neutral, I can hear a rattling noise maybe in the gear box?

The noise goes away when I step on the clutch.

What to do? Replace whole gearbox? Is it a flywheel problem?

my car is a 2.0 gts r32 4dr sedan, manual...

I had the gear box oil changed 2.5 years ago. I noticed the rattling in the last 3 months.

a mechanic says to wait until it goes then he'll fix it. somehow I think fixing it now is better than waiting for "it"(?) to go...

Thanks to anyone who helps.

Link to comment
https://www.sau.com.au/forums/topic/65248-r32-rattling-gone-when-on-clutch/
Share on other sites

mine use to do it but wasnt real bad. Clutch wore out not long after so i put new clutch and bearing in and was all good. depends how bad yours is. if it sounds like its about to seize id get it done soon as you dont want it to sieze and stuff your pressure plate

Ok.. i'll have to keep an eye out for gearboxes for sale...  thanks dude

why? the thrust bearing is part of the clutch. goes on the clutch fork, can buy them seperate or probably better of replacing clutch at same time. if it is that dont see why you need to look for a gearbox

I change gears fine. everything works.

There is this rattling noise that bothers me.  I don't hear it when cruising along with the exhaust and radio going.  But, while idling in neutral, I can hear a rattling noise maybe in the gear box?

The noise goes away when I step on the clutch..

Odds on it's a noisy clutch throw-out bearing. Cheap to fix...maybe $50+fitting, but it's been a long time since I bought just the bearing as it's usually changed when the clutch is replaced. Since the gearbox has to come out anyway to fix it, it would be worthwhile checking the condition of the clutch while its out.

I had the gear box oil changed 2.5 years ago.  I noticed the rattling in the last 3 months.

You're definately overdue for an oil change...I assume the level has at least been checked since it was changed ?? Still, if it's changing gears normally then it's probably just the clutch t/out bearing (above).

a mechanic says to wait until it goes then he'll fix it.  somehow I think fixing it now is better than waiting for "it"(?) to go....

A t/out bearing can be noisy for a very long time before it actually fails completely. Usually they just seize and the whole thing gets VERY noisy. Don't think I'd wait until it actually failed tho....

The worse the carrier bearing gets, the more it can wear out the clutch. If it seizes, it'll wear down the face of the bearing, then the clutch won't fully disengage. Some don't get like that but it can happen.

If there were a problem with the gearbox, I would imagine you would be able to hear it while driving, as neutral is not a loaded position. More likely to be the carrier bearing. If the noise sounds bad then get it changed immediately. Get the clutch done at the same time as OFENSV mentioned.

Should cost around the $600 mark for an upgraded clutch fitted drive away.

Would prolly cost around $200-$250 to just do the Carrier bearing (which only costs about $15). It often pays to do the rear main seal while your in there but it should be ok if it's not leaking at all.

There is a test you can do to tell the difference between the carrier bearing and gearbox noise. Just rest your foot on the clutch to take up the free play. Don't push it to the floor. This will push the carrier bearing up against the pressure plate but won't disengage the clutch. If the noise goes away like before, then the carrier bearing is the one.

yer mines goin too ... im gunna do it soon , so long as i can find meself a few hrs and no rain.

Do u need any specialized tools to get the box out ? i only got a few sockets and spanners :( .. oh and bugga gettin a mechanic to charge u 200 bucks to pull the box out !

The thrust/throw out bearing for the clutch only spins when the clutch is pressed in to the floor.

Yet you said the noise goes away when you step on the clutch?

Therfore it isn't the throwout/clutch bearing.

This is why you shouldn't sit at lights holding the clutch in as you wear the bearing out unnecessarily.

It will be one of two things.

One, its as simple as the input shaft bearing being stuffed. (Needs replacment)

Two, the hard casing has worn off the input shaft and main cluster gear in the box meaning all these parts will need replacing, therfore its cheaper to replace box altogether.

To rebuild it is going to cost some money. You would be better off to wait till it goes, then just replace it with another. RB20 boxes aren't worth much these days.

sorry to sound like a dumb ass but wat ? i thought if the throwout bearing was on its way if u pushed the clutch in the noise would go away ...

Ur sayin its the input shaft bearing ? umm isnt there only 1 bearing (that big round one) and a bush in the bak of block (brass) where shaft goes . Wats the "Input shaft bearing" . now im scared . I should just grab a new box . There is a small wind in the gears to i not sure if thats all bearing either . Wat u think , just grab new box to be safe , i dont wanna put the new bearings on and put it all bak in to find out i wasted all that time for nothing

Sorry to hijak ur thread wodaman .. me havin same issues :)

ummm , actually ... i was told that it is Actually the input shaft bearing .. John from UAS said thats wat was wrong wif my box . "welcome to nissan" he says :D damn it ...

So id prolly just get a new box in that case .

How would u tell if ur thrustrace bearing was goin then ?

When you press the clutch in, the clutch fork presses the thrust/clutch bearing into the clutch pressure plate fingers and the two parts of the bearings spin.

When you release the clutch the fork/bearing slide away from the fingers and the bearing spins as a complete assembly with the box input shaft. So it can't make any noise obviously.

If you press in the clutch in and its noisy then the clutch bearing would be shot, as the bearing will be spinning anytime the clutch is pressed to the floor.

If it isn't noisy it is fine.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Then, shorten them by 1cm, drop the car back down and have a visual look (or even better, use a spirit level across the wheel to see if you have less camber than before. You still want something like 1.5 for road use. Alternatively, if you have adjustable rear ride height (I assume you do if you have extreme camber wear), raise the suspension back to standard height until you can get it all aligned properly. Finally, keep in mind that wear on the inside of the tyre can be for incorrect toe, not just camber
    • I know I have to get a wheel alignment but until then I just need to bring the rear tyres in a bit they're wearing to the belt on the inside and brand new on the outside edge. I did shorten the arms a bit but got it wrong now after a few klms the Slip and VDC lights come on. I'd just like to get it to a point where I can drive for another week or two before getting an alignment. I've had to pay a lot of other stuff recently so doing it myself is my only option 
    • You just need a wheel alignment after, so just set them to the same as current and drive to the shop. As there are 2 upper links it may also be worth adding adjustable upper front links at the same time; these reduce bump steer when you move the camber (note that setting those correctly takes a lot longer as you have to recheck the camber at each length of the toe arm, through a range of movement, so you could just ignore that unless the handling becomes unpredictable)
    • I got adjustable after market rear camber arm to replace the stock one's because got sick of having to buy new rear tyres every few months. Can anyone please let me know what the best adjustment length would be. I don't have the old ones anymore to get measurements. I'm guessing the stock measurement minus a few mm would do it. Please any help on replacing them would be fantastic I've watched the YouTube clips but no-one talks about how long to set the camber arm to.
    • Heh. I copied the link to the video direct, instead of the thread I mentioned. But the video is the main value content anyway. Otherwise, yes, in Europe, surely you'd be expected to buy local. Being whichever flavour of Michelin, Continental or Pirelli suits your usage model.
×
×
  • Create New...