Jump to content
SAU Community

Recommended Posts

Hey guys,

I'm happy to announce that I can offer you fantastic prices of the entire NGK Iridium Range. These plugs are available for $16.50 a plugPrices are as follows:

4 x NGK Iridium IX = $66 ($5 extra if postage is required)

6 x NGK Iridium IX = $99 ($5 extra if postage is required)

8 x NGK Iridium IX = $132 ($5 extra if postage is required)

Pickup is available from the Gold Coast. COD will require a 10% deposit and all related costs are at your expense.

That's $16.50 a plug, singles can also be purchased for this price also.

Here is a basic reference chart for you all to go by:

BCPR6EIX-11

180SX & S13 Silvia CA18DET (4/1989 - 1/1991)

Z31 300ZX VG30ET (9/1983 - 10/1987)

Z31 300ZX VG20ET (9/1983 - 10/1985)

R31 Skyline RB20DE (8/1987 - 11/1989)

R31 Skyline RB20DET (8/1987 - 5/1989)

R32 Skyline RB20E & RB20DE (5/1989 - 8/1993)

R32 Skyline RB20DE (8/1991 - 8/1993)

R32 Skyline RB20DET (Late models)(8/1991 - 8/1993)

R32, R33 & R34 GTR RB26DETT (8/1989 - on)

R34 Skyline RB25DET (5/1998 - 6/2001)

S12 Silvia CA18ET (8/1983 - 5/1988)

S15 Silvia SR20DE (6/1996 - 1/1999)

BCPR5EIX-11

R31 Skyline RB20DE (8/1985 - 8/1987)

R32 Skyline RB25DE (5/1989 - 8/1993)

R32 Skyline RB20DET (Early Models)(5/1989 - 8/1991)

R33 Skyline RB20E (8/1993 - 5/1998)

Cefiro RB20DET (9/1988 - 5/1992)

Laurel RB20DET (1/1989 - 1/1993)

BKR6EIX

180SX SR20DET (1/1991 - on)

S13 SR20DET (1/1991 - 10/1993)

S14 SR20DET (10/1993 - 6/1996)

S15 SR20DET (6/1996 - 1/1999)

Toyota Soarer 1JZ-GTE (Early Models)(5/1991 - 8/1996)

Toyota MR2 3S-GTE (All Models)(10/1989 - 10/1999)

BKR6EIX-11

Toyota Soarer 1JZ-GTE (Late Models)(8/1996 - 4/2001)

Toyota Soarer 1UZ-FE (5/1991 - 9/1997)

BKR5EIX-11

R33 Skyline RB25DE (8/1993 - 5/1998)

R33 Skyline RB25DET (8/1993 - 5/1998)

R34 Skyline RB25DE (5/1998 - 6/2001)

BKR7EIX-11

N14 Pulsar GTI-r SR20DET (1990 - 1995)

VL turbo (1986 - 1988)

Please if you have any questions, or require plugs for a vehicle not listed above, feel free to contact me by either e-mail [email protected] or PM.

Regards,

Andrew

Link to comment
https://www.sau.com.au/forums/topic/65356-ngk-iridium-ix-spark-plugs/
Share on other sites

Moderators can you please delete my original, duplicate, post. I closed it by accident. Admin if you any concerns or questions please contact me.

Hey Gaki,

I have updated the listings to include you query. The plug is a BKR5EIX-11. If I can help you with anything else please do not hesitate to ask.

Regards,

Andrew Sullivan

Hey mate,

Yes I do keep the plugs you require, the GTIr takes BKR7EIX-11 plugs. I have updated the listing to include this vehicle.

Regards,

Andrew

Hey mate,

The plugs you require come pre gapped at 1.1mm (BCPR5EIX-11), this is the factory recommened gap. Although many people do regap them to 0.8mm, it's a personal thing.

Hope that helps,

Andrew

Guest
This topic is now closed to further replies.


  • Similar Content

  • Latest Posts

    • So could it be assumed it has been installed intentionally with potentially a power FC boost controller kit? 
    • Had my rig on Matt's dyno at PITS the other day. After a few years between tunes I added a few sensors and swapped intercoolers. Result. 553hp at 26psi. Not bad for an FJ20 that was built in 2007. The problem.. It filled the overflow bottle on hard runs which leads me to believe the head gasket isn't sealing. I have a coolant pressure sensor which was reading cap pressure at 22psi and occasionally overrunning to 23/24 psi on deceleration after a pull. It was not spiking. It has arp2000 head studs and a cometic gasket. As its been 18 years in service, I pulled the engine out and head off. Everything looks good but we obviously have an issue. Where I'm at.. Years ago I had the same issue, I checked the stud tension and they were all over the place. Some at 60 to 70 and some up near 90. I nipped them all to 100ft lbs and this stopped the water push until now. I believe this compromised the gasket back then. What do I do? 2 options are..  1) I bought arp 625+s, which I could put in with a new gasket. Thinking Kameari this time, reassemble and try again. 2) strip the block, get fire rings machined in with copper gasket and try that. I do not want to push it more than 28 to 30psi. I think the turbo will be out by then anyway. (G30-770). My other concern is the long term ability of a copper head gasket. Are they streetable for years? I feel like a new gasket with the new studs will probably suffice, but I don't know. Any thoughts welcome and advice on copper gaskets and fire rings. Thanks!
    • I'm a fan of the JZX110, and the Aristo. Big cruiser cars, and with the factory cars, super comfortable and feel like you're driving an armchair! And the JZ motors are a pretty nice engine too, especially with some basic mods.   The import process, and the need to be able to trust people, and the fact there's so many scammers around is what ever puts me off wanting to go through that ordeal!
    • I don't care for these at all, but at least the underside looks straight and not rusty. A good basis for a long life. Many cars from Japan have been lifted with forklifts and f**ked almost irrepairably.
    • Yes, but it's not dumb or dodgy. You can build a perfectly good boost controller from a pressure reg, a relief valve (looks same same as a reg if all from Norgren or SMC, for example) and a check valve. I ran one for years. Only superceded with  EBC because I could get one for cheaps and wanted finer control.   THis mod is certainly not a sketchy boost mod, provided the boost is kept below the "spin to death" threshold of the turbos.
×
×
  • Create New...