Jump to content
SAU Community

Recommended Posts

Okay im gona go down the strip tonight for the first time. Normally when i launch my car i ride my clutch and slowly roll forward then release. Will this give me a faulse start?? Should i have the handbrake up then release it doing this method or should i jst drop the clutch even though i normally dnt do this way off launching my car.

Should i do a little burn out before i race to will this give me more traction? and should i jst drop the clutch.

Thirdly, what do i need to take helmet etc, and any other points i should consider???

Link to comment
https://www.sau.com.au/forums/topic/65507-goin-to-runs-need-advice/
Share on other sites

You need helmet, rego papers, long sleeve pants/top and $45.

If you roll out of the staging beams before the green light, then yes you'll false start, but you'll still get an ET, so it's not really a huge mistake to make. The start area is flat, so you don't need your handbrake if you've got your clutch engaged - just drop the clutch on the last yellow light and you should get a good reaction time. To what degree you feather the clutch really depends on the tyres you're running - obviously the better traction you get, the quicker you should let the clutch out. It'll take some practice...i've been a couple of times now and I still can't get it right (shitty tyres don't help though).

As for the burnout, it's not really going to make much difference traction wise if you're running street tyres...much of a muchness really.

Good luck :(

1. Enter via the competitors gate (old rear entrance for the EC Racetrack).

2. Pay at gate ($45)

3. Park in the pits somewhere and fill out the form you are given (take a pen)

4. Line up at the scrutineering garage with your rego paper, license, filled out form and your entry ticket, you will get a wrist band.

5. Drive your car around to the garage and wait inline to have your car checked over (open bonnet, open boot, check helmet).

6. Drive your car back around into 1 of the 5 lanes and wait (usually about 30-40mins per run up until about 9pm then its about every 20-25mins because people leave/breakdown.

7. When its your lanes go just follow the guy infront of you and the marshall will mark the sticker on your screen and point you to lane A or B.

8. Burnout: You don't need/want to sit and smoke your rear tyres for 3hrs every run because all you are doing is wearing them out. All I do is drop the clutch from 3000rpm, let it spin (as it rolls forward) for about 5m and then just throw it in neutral and roll up to the staging line.

9. Staging: I always like to stage first before the other car, it gives you 10-30sec to settle your nerves, get comfortable in your seat (with your helmet on for a change). On the side tarmac part of your lane you will see a white line across the track, just move forward until your front tyres are close to this line, then watch the top 2 staging lights on the tree.

10. Launch (for me): Clutch in, handbrake off, hold the revs at 3000-3500rpm. When the lights go I just take off like a normal set of lights (so basically part drop, part ride the clutch). If it starts spinning the rears just back off abit, if it bogs well just hold on for a second or 2 until your revs pickup.

11. 1/4 Mile: Nail your gears, treat the car like you hate it or just drive like normal with the throttle flat, each to their own. Don't stop until you are past the big timing towers.

12. Follow the return lane all the way back past the staging around to the garage and grab your timing slip.

13. Repeat until either 10pm or your car breaks :(

Actually... I bet wsid.com.au has this written up somewhere :)

If it's your first nite seriously... don't worry about a burnout (its not required anyway except to scrub off the water) and don't try and cut an 11sec pass. Just learn to stage correctly (without looking like a knob and staging with your rear tyres) and get across the finish line in 1 piece without leaking fluid or breaking your clutch. As you get over those bits your times will drop by themselves...

Give me a wave if you see me [MOVEIT]

Happy drag racing !!

just drop the clutch on the last yellow light and you should get a good reaction time.
I actually take-off when I see the 2nd yellow light come on, it gives me consistent 0.1-0.3sec Reaction Times (which is why I win the majority of my races unless i'm up against a Pac "race" Car).

Launching on the last (3rd) yellow light will give you a 0.8-1.0sec R/Time :(

:)

I actually take-off when I see the 2nd yellow light come on, it gives me consistent 0.1-0.3sec Reaction Times (which is why I win the majority of my races unless i'm up against a Pac "race" Car).

Launching on the last (3rd) yellow light will give you a 0.8-1.0sec R/Time :(

:)

lol, no wonder I can't get any better than a 0.2 R/T - I'll try that next time :)

I was keen to go tonight, but something's come up, so im aiming to be there again next week instead.

Good luck tonight fellas - look forward to reading about that 13 sec pass benm :)

Also, it doesn't matter how long after the green light comes on before you actually take off. Your ET is recorded from the time you cross the second staging beam until you cross the finish line. Plenty of cars sit for a while on the line getting set as they are after a time not the win. But if you really want to beat the car in the other lane, then take off on the last yellow (or second one if you have slow reflexes :() The main things is getting used to the proceedure, staging and gear changes. Have fun!

Have fun, my first time I loved it.. I also tried launching on different RPM's as each car's setup is different you might find that you could drop on each run on the last yellow but use different RPM lauches to find the right amount of traction to wheelspin that gets your turbo and ass moving :(

good luck.. :)

I have heard some people complain about of lack of traction using street tyres, but I personally haven't had any trouble. 1.8 60 ft on my first pass with an open diff (S3 RX7 Turbo) on street tyres. Alot of it is more than likely due to street tyres and 30+ psi. Use some semi's or drag radials and you will see the sub-1.8 60ft's :( But generally, it is stickier and also helps if they have a Test and Tune on that Wednesday for a big meet the following weekend.

silver gts-t - running street tyres, in my personal experience the track does not seem as sticky as the road! But I was told that it wasn't prepared properly for that particular meet.

Changing 2nd to 3rd my car actually fishy'd abit.... thats with Exhaust, Front Mount and Boost..... 13.9 first night ever at the drags with tyres at 36psi.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Haha, i kow right? Could have bought so many cars for the same amount of money (or less) but driving Unicorn gives you at least +1mln to style 😅. Like wise man said "life's to short to drink cheap wine and drive boring cars" 😉
    • Newbie here, proud owner of an Autech 260RS. I'm on the hunt for wiring diagrams specific to the 260RS, particularly S1. I've ran my eyes through R33, R34 Diagrams, there are some similarities, however continue to find incorrect wire colours and pins on connectors in the 33,34 diagrams.   I was hoping someone could point me in the right direction? I'd be happy to pay for the originals in Japanese. I can translate them, at least they would be accurate.   Any help please would be greatly appreciated, never heard an RB26DETT before let alone driven one, and I've got a spaghetti monster of goodness to sort out.   Cheers Benny  
    • Hey all  im wondering if you can help me please I have put a rb20 box in my r34 gtt as my auto packed up and a friend had a spare box I know it’s not ideal but it will get me up and running for now. we have done the conversation and everything is working great but my Speedo we got a s13 speed sensor but my Speedo reads double now and I bought a speed converter but still not having any luck.  so I thought I’ll reach out and pick your brains  any help would be appreciated please as I wanna drive my car again 
    • Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
×
×
  • Create New...