Jump to content
SAU Community

Recommended Posts

Hey guys,

I have a 94 gts-4 skyline. Its recently imported and had a cr@p stereo in it. So i began to replace componants. I used the head unit install guide, top stuff. That went smoothly, then i discovered at an earlier date i had blown upo all 4 ic's in my head unit ( the built in amp) so i hooked up an amp i had to run the speakers. I got decent cabling- triplke insulated stinger rca's and triple insulated shnider (or how ever u spell it) amp wiring kit. I did this cause i had heard that engine noise on r33's can be a problem in aftermarket stereo's. Im looking for some advice about what could fix the problem. Should i run the rcas down another side of the car? Any advice would be helpful,

Thanks in advance

Pete

:Bang:

Link to comment
https://www.sau.com.au/forums/topic/66318-engine-noise-making-life-difficult/
Share on other sites

power cables should not be run Parallel with rca's clean all earths that come from deck and to the amp, check that your bat is clean and free from crap, change your sappressor on the altornator. See how that goes, also i have found if you have your gain turned up to far on the amp it will cause unwantied shit noise

you should get no engine noise whatsoever on an R33 if your cabling is wired correctly, even with relatively cheap face unit.

Just try moving your wiring around. Otherwise quite likely to be the amp. Is it sitting near the fuel pump in your boot??

you should get no engine noise whatsoever on an R33 if your cabling is wired correctly, even with relatively cheap face unit.  

Just try moving your wiring around. Otherwise quite likely to be the amp. Is it sitting near the fuel pump in your boot??

Where abouts is the fuel pump in the boot - on the right?

My engine noise is driving me crazy. I have RCAs run down the left side of the car, noise supressor on RCAs, noise supressor on amp but still heaps of noise.

Would getting shielded RCA cables and running them down the middle help?

the amp is decent- i think. Its an older pioneer one- not sure on the model code, but hasnt been a problem when i have run it previously in my old vl. The amp is screwed into the sub box on top, and it just sitting in the boot. If the fuel pump is the thing on the right hand side of the boot, under the plastic cover- no it isnt, the sub is on the left hand side, the gap is slightly larger so the sub box can be pushed back further, using less space. The earth on the head unit is located im the transmission tunnel, right ner the shifter. Could that be the problem? it isnt as noticable when i only run the sub and no speakers. The noise also increase pitch (like how high the noise is) as my revs gain.

any help is appreciated

thanks

Pete

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
    • Actually, I'd say all three are the automatic option. Just the different trim levels. The manual would be RSFS, no? 
×
×
  • Create New...