Jump to content
SAU Community

Drift Practice Night - Sunday 20th March, Full Lock Motorsport.

aKTiVE

By aKTiVE,
in Archived Events

 Share

Recommended Posts

aKTiVE Collaborator

aKTiVE

Posted
Posted

Hey Guys,

For a change we are having the Drift Practice night on a Sunday night, so that all the people that want to compete but cant get there on time during the week can now have their chance !

When: 6pm - 10pm, Sunday 20th March 2005

Where: Calder Park, Calder Freeway, Keilor

Cost: $80 per driver (includes one pit crew entry), Spectators $10

How to enter: All entries will be taken at the gate. Entries will be capped at sixty. Those who arrive early will have priority.

Car Requirements: Cars must be of a safe and roadworthy standard. They must have working headlights and break lights. Fire extinguisher and roll cage are not essential but recommended. Seat belts must be working and of a safe standard, harness’s permitted. All lose items must be removed from the car. It is recommended that you remove your front bumper to avoid damaging it.

Driver Requirements: Drivers must be licensed. Drivers must wear long sleeve top and long pants made of natural fibers e.g. cotton. Helmets must also be worn and are available for hire at Calder Park for $20.

Do not wear shorts and a t-shirt we know its getting warmer but this is for your own safety.

Passengers: Passengers are strictly not permitted.

Prizes: Prizes will be awarded to the top three drifters on the night courtesy of Autobarn Sunbury . The top three drifters are decided by a top eight D1 style drift battle. The battle begins at 9:15pm presentations at 9:50pm.

Bryce Steele and the boys from Dr Rubber (Victoria Pde) will be there on March 20 with used and new rubber, if you are interested. Bryce will also have a truck with some race specific product for sale like helmets, gloves and even RON 110 fuel!!

Drift tyres will be available for sale and fitting at approximately $15 per tyre.

BEGINNERS

Remember the bottom section of the track will be open for practice for BEGINNERS ONLY, and we will close it at 9.15pm. Any beginners using this section of track are able to drive on the main circuit if they feel capable. Beginners will be instructed on how to drift by the Full Lock Drift Team/FLM Racing free of charge.

Hope to see you all there !

Roy Grand Master

Roy

Posted
Posted

Did we speak tro one another? Should have said hello :cheers:

The guys running the day were friendly and despite my drifiting under yellows, didnt ream me like i was expecting once my shortcoming had been pointed out to me:(

Yeh, it was good fun...but christ its hard on the car. It was my first time ever trying to drift and found giving it a punt in 3rd gear on boost was way more dangerous then when sliding around in 2nd gear:(

I thiunk i spun more then any other car, winding down the boost and upping the rev limiter helped but i still sucked:(

Still good fun though. RowdyR32 was the grey R32 GTST with the RB26, and 46n2 was the white stocka GTST

hellrazorette Collaborator

hellrazorette

Posted
Posted

Good to see you guys giving it a go :(

Splitting the track into 2 looks to have been a good idea though. Glad to see there was more supervision and safety officers there this time round to sort out any hassles, thankyou! Good night in all I think :D

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      I wanted to try and preserve the front bumper as long as possible, they're not cheap and are made to order in Japan. Taking inspiration from my previous K11 Micra build where I made an undertray for the Impul bumper, I did the same for this BN Sports bumper but a little slimmed down.  This time round I only made a 'skid plate' (if that's the correct wording/term) for just the bumper surface area, the Micra version covered the gap like an undertray. Starting off with a sheet of mild steel approx. 0.9mm thick 4ft x 2ft in size. I traced around the bumper, cut it out and cleaned the edges. Luckily I was able to get two halves from one piece of metal In the video I installed it as is, but I've since then I've removed it to spray and add a rubber edging trim. The rubber trim is suitable for 1-2mm and it's a really nice tight fit. The bolts had to be loosened due to the plates being too tight against the bumper, the trim wouldn't push on I used some stainless M6 flat headed bolts for a flusher finish (rather than hex heads poking down), I believe this style fastener is used for furniture too incase you struggle to source some. The corner's are a little wider, but this may be an advantage incase I get close to bumping it  The front grill got some attention, finally getting round to repairing it. Upon removal one fixing pulled itself out of the plastic frame, one side is M8 that fixes inside of the frame, where as the other side is M5. Not knowing I could get replacements, I cut down an M8 bolt, threaded it inside the frame along with a decent amount of JB Weld.  The mesh was replaced to match the bumper. One hole on the bonnet/hood had to be drilled out to 8mm to accommodate the new stud, once the glue had set it could be refitted. I think the reason the grill was double meshed was to hide the horn/bonnet latch (which makes sense) but I much prefer it matching the bumper Bumper refitted and it's looking much better IMO The Youtube video can be seen here: https://www.youtube.com/watch?v=bVZP35io9MA
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      The video for the servicing and fuel filter change can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44 One of the main jobs I wanted to do before the car officially went on the road, was to remove the awful looking blue silicone hoses. There's nothing wrong with having coloured silicone hoses, but I realise as I'm getting older I prefer monotone engine bays with a splash of colour on the engine cover(s). I cover this in a lot more detail in the Youtube video, so unfortunately there's limited photos of the process. The intercooler, upper radiator, boost vacuum and upper breather hoses were all changed to black silicone with mikalor clamps. The only blue left is a blanking cap at the back of the inlet manifold and the GReddy pulleys (which will be replaced for stock when the cambelt gets replaced) While the intercooler pipes were off I gave them a quick clean/polish too A before photo I do have a replacement air filter on its way. Fuse box covers were painted blue, they're now satin black Another job on the list while the bumper was off, is to add some mesh https://live.staticflickr.com/65535/54737966256_99b28bfa30_c.jpg[/img] I was hoping to use some thin wire to secure it, but it seems I've misplaced it and the wire I had was too thick to twist easily. I ended up using cable ties for the time being https://live.staticflickr.com/65535/54737131882_c2b7989dcc_c.jpg[/img] Was pleasant to see this https://live.staticflickr.com/65535/54737131627_8b2aab13b3_c.jpg[/img] The last thing to do was to fix the front grill and re-mesh that to match but I ran out of time The Youtube video can be seen here: https://www.youtube.com/watch?v=R4FsF6tgizE&t=23s
×
×
  • Create New...