Jump to content
SAU Community

*does anyone know to clock bak speedo's*

ZILR-34

By ZILR-34,
in Engines & Forced Induction

 Share

Recommended Posts

Guest two.06l

Guest two.06l

Posted
Posted
hey people as the title says, i would like to know how to turn back the km's on the speedo, i have a R32 and i just rebuild the whole engine so i would like to clock it back.  

cheers

bill

maybe you should have posted this in the Japan section.....as they seem to be expert at it.

R31Nismoid Grand Master

R31Nismoid

Posted
Posted

thats actually illegal, might change on state.. but i doubt that.

You can only do it with a change of dash, and then there is paperwork you can fill out to meet the requirements.

jsut cause u did the motor doesnt mean... bushes... diff, gearbox, shaft, chassis aint dont the km's

Bass Junky Grand Master

Bass Junky

Posted
Posted

Maybe you shouldn't try to rip people off.

How would you have felt buying a car and then finding out it had done 100,000klms extra.

Happened to me. Don't be an arsehole and try and make a quite buck, because it will come back to you eventually. And if you do wind it back, I hope it does come back to you, HARD.

ZILR-34 Experienced

ZILR-34

Posted
  • Author
Posted
thats actually illegal, might change on state.. but i doubt that.

You can only do it with a change of dash, and then there is paperwork you can fill out to meet the requirements.

jsut cause u did the motor doesnt mean... bushes... diff, gearbox, shaft, chassis aint dont the km's

hahhaha frist i would like to say. doin mods to ur car is illegal, like intercoolers, BOV's, boost controllers, pod fillters etc... wat makes dis different u idoit?

second of all yes i have changed everything i built my R32 ground up. all the parts are pritty much new. i got a new after market speedo the one which goes to 310km/h so the old one i would like to turn it bak and sell it with low km's on it.

the speedometre is already out all i need is a guide to get wat im after...

bill

Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Dose Pipe Sutututu
      S1 rb25/s14 starting problem

      By Dose Pipe Sutututu · Posted

      When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • PranK
      My BMW E39 528i touring

      By PranK · Posted

      Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • 25zenki
      S1 rb25/s14 starting problem

      By 25zenki · Posted

      Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • CRSKmD
      R32 Sedan - Grip and Drift (have my cake and eat it too build)

      By CRSKmD · Posted

      yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...