Jump to content
SAU Community

R32 install

grandmasterb

By grandmasterb,
in Car Audio & Electrical

 Share

Recommended Posts

grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted
Great, should be easy to get to then! is the space for it large? :/

I've just bought an Eclipse 4x70W RMS amp... whats the factory one rated at?

I hope the new one will fit in the same spot...

Very easy to access, you can fit another amp there i suppose but it might take a little bit of messing around as the stock amps are usually very small. You will work something out though im sure.

Wobbz Contributor

Wobbz

Posted
Posted
Very easy to access, you can fit another amp there i suppose but it might take a little bit of messing around as the stock amps are usually very small.  You will work something out though im sure.

My brother removed it for me today while he was doing the rest of the compliance work. He said there was no chance in hell my new amp would fit (and its not that big!)

grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted
My brother removed it for me today while he was doing the rest of the compliance work. He said there was no chance in hell my new amp would fit (and its not that big!)

You can fit an amp in same location but it requires some work like i said. You need to move the rear wiper assembly motor and new mounting holes for the amp. You need a bracket for the front end of the amp so you have something to affix too. Your better off fixing the amp somewhere else like the back of the seat, spare tyre well or the side of the wheel arch depending on what else you ahve in your boot. Play around with it and see where works best for you and the install your doing as there are plenty of options to mount it in there.

grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted
dont listen to gmb the only skyline he has is looking at timmyb's

WHAT DOES THIS HAVE TO DO WITH THE TOPIC, PLEASE KEEP THE SUBJECT ON TOPIC WOLVERINE11 AND IF YOU HAVE A PROBLEM WITH ME KEEP IT OFF THE FORUMS AS ITS NOT THE TIME OR THE PLACE :bs!:

grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted
it is when u keep crapping on to people about shit u dont know,

how can u give all this advice on skylines when u dont even have one??

WHO says i dont know, it doesn't take a rocket scientist to figure it out numb nuts. Like i said SAu is about helping people out, not sledging people or having a go to publically humilate people. If you dont have anything contructive to say and all you want to do is have a go at me then you know where i am. Leave it off the forums and stop hijacking peoples threads with posts that have absolutley no realevance to the topic :usuck:

SkyGTRline Mentor

SkyGTRline

Posted
Posted

LADIES!!!

everyone has a right for there input... whether its right or not.. Too bad..

Everyone is here to help each other... whether you have a skyline or not... if you know something and want to share it... Feel free..

Leave the crap off the forums..

grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted
LADIES!!!

everyone has a right for there input... whether its right or not.. Too bad..

Everyone is here to help each other... whether you have a skyline or not... if you know something and want to share it... Feel free..

Leave the crap off the forums..

COULDN'T OF SAID IT BETTER MYSELF IF I TRIED SKYGTRLINE. ITS A PITY THAT THERE ARE SOME PEOPLE OUT THERE THAT INSIST ON FARKING IT UP FOR THE REST OF US, AND ESPECIALLY THOSE THAT LIKE TO HAVE CHEAP SHOTS AT OTHERS THATS NOT EVEN RELEVANT TO THE TOPIC :kick:

grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted

Ok so all components aquired for the system and i have the materials for the SD of the front doors. I have my cabeling and the only thing im waiting on is a maxiblade type fuse. I'll take a couple of pics along the way and let you know how it all goes. Im aiming to ahve the complete system installed and doors SD in 2-3 days. Depending on how much help i get from a certain SAU member :D

Baz Experienced

Baz

Posted
Posted

A quick question, just installing the 6x9's on my R32 four door. I've just finished mounting, cutting and installing the 6x9's on my rear parcel shelf. How has everyone run the wire from there rear speakers to the stereo? I'm trying to follow the existing wiring of the factory loom but first off im having difficulty removing the rear seats (anyone removed them before?)

B0oStEr Mentor

B0oStEr

Posted
Posted
A quick question, just installing the 6x9's on my R32 four door. I've just finished mounting, cutting and installing the 6x9's on my rear parcel shelf. How has everyone run the wire from there rear speakers to the stereo? I'm trying to follow the existing wiring of the factory loom but first off im having difficulty removing the rear seats (anyone removed them before?)

No tricks, just get your fingertips under the seat on one side and yank it up hard then do the other side and it will lift out.

Remove the bolt on each side that holds the back rest then lift it up and ease it out past the seatbelts.

  • 2 weeks later...
grandmasterb Grand Master

grandmasterb

Posted
  • Author
Posted
when i took my back seat out i just used the end of a shifter and it went pop and it was out easy  :uh-huh:

i wish it was that easy for me and TimmyB yesterday, took us 10 mins to get the biatch off.

The clips appeared to be bent and we just couldn't get them free :chairshot

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • joshuaho96
      Speed Sensor replacement

      By joshuaho96 · Posted

      Drain it. I got official Matic D but you can get whatever is listed as Matic D compatible.
    • QB6SAGR
      Tein Circuit Master- rebuild worth it?

      By QB6SAGR · Posted

      Thanks guys,  Yeah I should at least have them dynoed, at least then I know what I've got as a starting point.  The springs on these are hard as rocks. I vaguely remember Russman saying he was going to sell the shocks to me with the rocks fitted, as he was keeping the softer springs for his new setup.  I didn't click at the time but of course that was to let me know the shock/spring wouldn't be matched.  I also remember pricing up new springs around 2014-15, but, house, money etc. it never happened. So that was another reason to have them rebuilt. I have rebuilt the forks on many motorcycles so I think I could handle the seals on these easily enough, but getting the valving right would be a rabbit hole I cbf exploring.  Duncan, interesting to hear RP was tuning these back then. I might give them a call.  In the mean time I have been busy fitting sway bars. The Whiteline rear sway bar I purchased 15 years ago finally got fitted, along with the Whiteline front bar that showed up last week. Just waiting on new links for the front sway bar to finish that off.  And my spare set of advan AVS VS5's should be back from the powder coaters in a Pearl White finish sometime this week, with a set of Hankook RS4's lined up for fitting.  And then I just have all the suspension bushes to do. A comprehensive kit is on the way... Lots to do before the Ararat hill climb. Cheers guys 🍻   
    • funkymonkey
      Howdy Y'all

      By funkymonkey · Posted

      Nice car! I’m glad folks in the US have gotten past the FnF and are buying real cool cars like the 260RS I was with a bunch of mates in Portland about a year ago and spotted a green Stagea (just a regular 2.5T AWD) parked about 2 blocks away and they were like “a what?” So I made a bet with them for a round of beers and said “ok one of you run down there and tell me if the steering wheel is on the correct side” 5 mins later the American comes trudging back up the hill and goes “he’s right guys. Ok what beer do you want?”
    • Dose Pipe Sutututu
      Starting again

      By Dose Pipe Sutututu · Posted

      Should replace OR drop the tank, give it's good clean. Might be worth replacing that entire fuel level/pump/cradle thing with this: https://frenchysperformancegarage.com/products/fpg-s13-180sx-r32gtst-single-pump-hanger-kit-billet-hat-6-v3-fpg-089?gQT=2  
    • R33_Guy
      Speed Sensor replacement

      By R33_Guy · Posted

      Thank you so much for the help
×
×
  • Create New...