Jump to content
SAU Community

Max power through stock RB20 bottom end?

pitchd

By pitchd,
in Engines & Forced Induction

 Share

Recommended Posts

pitchd Proficient

pitchd

Posted
Posted

hey guys,

new motor is being dropped in atm...

RB20DET - completely stock internals

RB25 gearbox

hks twin plate clutch

550cc denso injectors

gtr fuel pump

tomei coilpacks

apexi power fc and handcontroller

blitz dsbc

z32 afm

trust cooler

grex oil cooler

eastbear earth wire kit

buddyclub 3.5" turbo back exhaust

hks t04e turbo on hks cast manifold with hks 28mm external gate

hks 1.2mm headgasket

i wanna run around 220rwkw for now with it... so prolly around .8bar on a light tune

motor has good compression... and is 80,000kms old

now how long will this last?

- adz

dangerous_daveo Grand Master

dangerous_daveo

Posted
Posted

A day on a bad tune, for a long time on a good one.

If you can try and find the "260rwkw on an rb20" thread its got heaps in there man.

End of the day, its tune that is going to either make or break it.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • bullet300
      Ecumasters Det3

      By bullet300 · Posted

      Wiring the car up today so will report back for anyone else that searches this in future.
    • RBW49N
      Factory oil temp sensor in a RS4V without gauges?

      By RBW49N · Posted

      The light comes on from low oil pressure. Not temp. Did you do a rebuild or just add an ecu etc?  What oil are you using and where are you getting the pressure reading from
    • Chi-Town
      Factory oil temp sensor in a RS4V without gauges?

      By Chi-Town · Posted

      So like the title says my 97 rs4v has a oil temp sensor but no triple gauges as it was originally factory navigation. My current setup is not using the factory oil pressure sensor as I'm running a link ecu and a real sensor.  I did leave the oil temp sensor in. So now as I was working on first start up and bleeding coolant I get the oil light on the dash faintly as the oil temp gets to about 60-70c. Oil pressure is 45psi at idle at the same time.  I'm wondering if the temp sender doing this?  
    • Chi-Town
      C34 RSFour V Build in the US

      By Chi-Town · Posted

      Well it runs again!  This was a definite case of while I have it apart lol Everything except the body and interior has been restored, refinished, or replaced.  @socal_stagea is my IG if you're bored and want to see all the pics.
    • Manur33
      R34 engine swap Rb25de neo to s1 Rb25det

      By Manur33 · Posted

      I already got plug and play Link ecu G4X. Main concern is that the de loom works on s1 motor or not? I already rewired injector and coils loom to suit my bosch injectors and bosch vag coil. I’m not running any Iacv. For cas running the nz wiring kit i bought the neo plug one so it suits the wiring but don’t know it works or it doesn’t matter they work the same on every motor. For wastegate solenoid do i need to wire straight from ecu? What can i do for iat sensor to work or same run from ecu? For Vct solenoid, right now i got s1 vct solenoid on motor so do i need to remove neo connector and add s1 connector to work? Any other thing i missed i need to do to make the motor working on de loom. Any different mechanism on neo vs s1?
×
×
  • Create New...