Jump to content
SAU Community

Recommended Posts

Hey guys, I was talking to a few of you who said you would be keen for this cruise. All are welcome.

Meet: Spears Point Park (10.30am, leave at 11am)

Destination: The Haven (Terrigal) via Swansie

Once we are all down there we can decide if we go for another drive or if there is anything else to do. Suggestions welcome.

Oh and don't forget your UHF's....with batteries :) (will decide channel on the day)

Please post if you would like to attend.

Attending:

NYL83R

NZM.031

d-d

dean1285

wizard2k

Lenno

GRUNTN

GTS4dood

michadoo

Maybes:

Birnie

eXc

sneedsy + 5-7

DRFT32

sindows

OohArrGTR

Link to comment
https://www.sau.com.au/forums/topic/71512-newcastle-to-central-coast-15th-may/
Share on other sites

  • Replies 82
  • Created
  • Last Reply

Top Posters In This Topic

I just changed plans for a motorbike course from 1st of May to 15th of May because of a pub crawl on the Saturday night.  Guess I miss out again!

good on ya, make the course for the 8th :rofl:

Very nice choice - your right, they suit the car well.  Not too ricey and not too plain, just right!  Need to drop that she-bitch now.

thanks, and it will be getting lowered soon hopefully :P

:headspin: hmmm, the autosalon is on the sat and sunday, so if you wanted to see it you could go on the sat. Leaving sun open for cruising :rofl:

We are getting some good numbers for this cruise, it should be a good day.

Hey guys, I was talking to a few of you who said you would be keen for this cruise. All are welcome.

Meet: Spears Point Park (10.30am, leave at 11am)

Destination: The Haven (Terrigal) via Swansie

Once we are all down there we can decide if we go for another drive or if there is anything else to do. Suggestions welcome.

Oh and don't forget your UHF's....with batteries

Please post if you would like to attend.

Attending:

NYL83R

NZM.031

sindows

d-d

dean1285

wizard2k

Lenno

Maybes:

Birnie

eXc

sneedsy + 5-7

I dont know how to get to spears point park... i dont even know what part of newie that is... Im from the CC and will drive to newie and then back to the CC with ya'll....

Could you show me where spears point park is?

Cheers...

Also i dont have a UHF :D (N)




  • Similar Content

  • Latest Posts

    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
    • Probably not. A workshop grade scantool is my go to for proper Consult interrogation. Any workshop grade tool should do it. Just go to a workshop.
    • In my head it does make sense to be a fuel problem since that is what I touched when cleaning the system. When I was testing with the fuel pressure gauge, the pressure was constantly 2.5 bar with the FPR vacuum removed. When stalling, the pressure was going up to 3.0 bar (which is how it should be on ignition).
    • ECUtalk pages don't mention they support the ABS computer (consult port has more than one CAN), so you might just need a different scan tool. But, I would expect ABS is a different light to the brake warning/handbrake light, do you see an ABS light come on for a few seconds when you turn the key from ACC to IGN? But since you said: I'd have a look at the ABS sensors in the rear hubs to make sure they are not damaged, disconnected etc.
×
×
  • Create New...