Jump to content
SAU Community

Recommended Posts

  • Replies 104
  • Created
  • Last Reply

Top Posters In This Topic

My best time is 1:16. Went out yesterday but only managed a 1:20 (consistant tho).. My brake pads where cheap and nasty (aka.. fadeeee so I was braking very early)... plus my tyres can't put the power to the road or grip well under brakes.. all in all not too bad at all! merli is right, its easier to drive a slower car fast! My accerator pedal was like a handbrake!

I had a ball.. Was a little frustrated about the brakes being spungy and a bit meh but the car was running better than it ever has! Was weird to be back out on the track, its been a while.

I will swap out the pads for sbs ceramic pads, flush the fluid again (did it on saturday) and then throw on some decent tyres and aim to better my 1:16.. which should not be too hard.

Bendix are a street pad, they hold up to wakefield park "okay" but you need to give them a rest every few laps.

however they chew the rotors ALOT more than most other pads. So yeah you save on pads but your rotors wont last as long.. meh

I used race brakes RB74 and they where fantastic, the sbs are better again. You get what you pay for, i was racing on $150 pads on the weekend and will change to the sbs pads ASAP!

With the rb74's my car was on the track at wakefield for a full hour (first me driving 20 minutes, then someone else then me again.)

no just fronts

for that kind of money you may as well fork out another $30 for Project Mu HC Titan Kai Pads. One of THE BEST pads you will ever come across and that's speaking from first hand experience. They work from cold and are rated to 800 Degrees. This is awesome for a performance pad considering Endless's top of the line CC-R pads work in a heat range of 150 ~ 800 Degrees.

Project Mu pads are also readily available in Australia.

you wont look back

Titanium Carbon Metal Composite.

http://www.project-mu.co.jp/e/product/hc-t.html

On the topic of brakes, Race Brakes now distribute a brand called Galfer. They make Braided Brake Lines for around $450 for a full set. Very good lines and well worth the money to improve your pedal feel.

on brakes I just fitted a set of Nismo lines I picked up in japan. having previously bought aus made ADR approved lines I can say that the nismo ones are much nicer still. they are a teflon line covered by a stainless steel braid which is then sheathed in teflon covering. this prevents dirt working into the braid which can be a problem. oh and they were about half that $450 price....

also I bought some Endless brake pads whilst in japan which I'll whack in this week. the GTR already has endless pads on the rear and I dunno whats on the front. it stops very well but needs 1 or 2 stops when cold to start working.

I have previously found the Endless pads to be excellent. have also tried some project mu's but can't remeber which type (they have quite a few). they were quite good too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • Hi, is the HKS  Tower Bar still available ? negotiable ? 🤔
    • From there, it is really just test and assemble. Plug the adapter cables from the unit into the back of the screen, then the other side to the car harness. Don't forget all the other plugs too! Run the cables behind the unit and screw it back into place (4 screws) and you should now have 3 cables to run from the top screen to the android unit. I ran them along the DS of the other AV units in the gap between their backets and the console, and used some corrugated tubing on the sharp edges of the bracket so the wires were safe. Plug the centre console and lower screen in temporarily and turn the car to ACC, the AV should fire up as normal. Hold the back button for 3 sec and Android should appear on the top screen. You need to set the input to Aux for audio (more on that later). I put the unit under the AC duct in the centre console, with the wifi antenna on top of the AC duct near the shifter, the bluetooth antenna on the AC duct under the centre console The GPS unit on top of the DS to AC duct; they all seem to work OK there are are out of the way. Neat cable routing is a pain. For the drive recorder I mounted it near the rear view mirror and run the cable in the headlining, across the a pillar and then down the inside of the a pillar seal to the DS lower dash. From there it goes across and to one USB input for the unit. The second USB input is attached to the ECUtec OBD dongle and the 3rd goes to the USB bulkhead connected I added in the centre console. This is how the centre console looks "tidied" up Note I didn't install the provided speaker, didn't use the 2.5mm IPod in line or the piggyback loom for the Ipod or change any DIP switches; they seem to only be required if you need to use the Ipod input rather than the AUX input. That's it, install done, I'll follow up with a separate post on how the unit works, but in summary it retains all factory functions and inputs (so I still use my phone to the car for calls), reverse still works like factory etc.
    • Place the new daughterboard in the case and mount it using the 3 small black rivets provided, and reconnect the 3 factory ribbon cables to the new board Then, use the 3 piggyback cables from the daughterboard into the factory board on top (there are stand offs in the case to keep them apart. and remember to reconnect the antenna and rear cover fan wires. 1 screw to hold the motherboard in place. Before closing the case, make a hole in the sticker covering a hole in the case and run the cable for the android unit into the plug there. The video forgot this step, so did I, so will you probably. Then redo the 4 screws on back, 2 each top and bottom, 3 each side and put the 2 brackets back on.....all ready to go and not that tricky really.      
    • Onto the android unit. You need to remove the top screen because there is a daughterboard to put inside the case. Each side vent pops out from clips; start at the bottom and carefully remove upwards (use a trim remover tool to avoid breaking anything). Then the lower screen and controls come out, 4 screws, a couple of clips (including 3 flimsy ones at the top) and 3 plugs on the rear. Then the upper screen, 4 screws and a bunch of plugs and she is out. From there, remove the mounting brackets (2 screws each), 4 screws on the rear, 2 screws top and bottom and 3 screws holding in the small plates on each side. When you remove the back cover (tight fit), watch out for the power cable for the fan, I removed it so I could put the back aside. The mainboard is held in by 1 screw in the middle, 1 aerial at the top and 3 ribbon cables. If you've ever done any laptop stuff the ribbon cables are OK to work with, just pop up the retainer and they slide out. If you are not familiar just grab a 12 year old from an iphone factory, they will know how it works The case should now look like this:
    • Switching the console was tricky. First there were 6 screws to remove, and also the little adapter loom and its screws had to come out. Also don't forget to remove the 2 screws holding the central locking receiver. Then there are 4 clips on either side....these were very tight in this case and needed careful persuading with a long flat screw driver....some force required but not enough to break them...this was probably the fiddliest part of the whole job. In my case I needed both the wiring loom and the central locking receiver module to swap across to the new one. That was it for the console, so "assembly is the reverse of disassembly"
×
×
  • Create New...