Jump to content
SAU Community

R32 "A" pillar pod

nedb

By nedb,
in Wanted to Buy

 Share

Recommended Posts

gts4diehard Rising Star

gts4diehard

Posted
Posted

hi, if you want to do it the cheap way and have a couple of hours spare - heres how.

goto bunnings etc and buy a 50mm pvc pipe with a 45 degree bend- take your gauge with you to check for good fit.

cut a wavy curve into one end that fits the profile of the a pillar - its a little tricky and takes a bit of filing

take a pice of metal about 100mm long, 15 mm wide and 1 mm thick, the piece out of the expansion slots in the back of your computer works good.

bend each end of metal 90 deg and up about 15 mm and fit your new bracket inside the pipe

drill a hole either side of pipe and countersink it, rivet the bracket to the pipe.

fit pipe and bracket to car, drill a hole through pipe at 90 deg to bracket - so you can drill through it (making pilot hole in pillar) and also to put the screwdriver into so you can screw gauge hole(pipe & bracket) to a pillar.

get your mum or missus to sew a leather sock that is the same diameter as the pipe and 230-40 mm longer than pipe. it will be sewn with seam on the outside. turn it inside out so that the seam is hidden.

fit sock to gauge holder , tuck in near edges that is against a pillar and glue it.

there should be be some over hang at the end where you will fit the gauge.

push the sock over hang into gauge holder then fit gauge into it, gauge should be a snug fit and hold sock in place, if not wind some tape(e.g. insulation tape) around gauge to increase diameter until it makes a snug fit.

then if you've done a good job you will have a leather gauge holder that looks really good.

P.S. you need to be careful or you will end up buying a plastic gauge holder to cover up any mistakes. oh yeh, std disclaimer if anything goes wrong, do it at your own risk ....

I will post up some pics of mine sometime ... it cost me about $5 to do,for pipe and leather offcut.

Link to comment
https://www.sau.com.au/forums/topic/71645-r32-a-pillar-pod/#findComment-1331850
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Kinkstaah
      Mistakes were made, my R34 Story

      By Kinkstaah · Posted

      I'm back from the dyno - again! I went looking for someone who knew LS's and had a roller dyno, to see how it shaped up compared to everything else and confirm the powerband really is peaking where Mr Mamo says it should. TLDR: The dyno result I got this time definitely had the shape of how it feels on the road and finally 'makes sense'. Also we had a bit more time to play with timing on the dyno, it turns out the common practice in LS is to lower the timing around peak torque and restore it to max after. So given a car was on the dyno and mostly dialled in already, it was time for tweaking. Luis at APS is definitely knowledgable when it came to this and had overlays ready to go and was happy to share. If you map out your cylinder airmass you start seeing graphs that look a LOT like the engine's torque curve. The good thing also is if you map out your timing curve when you're avoiding knock... this curve very much looks like the inverse of the airmass curve. The result? Well it's another 10.7kw/14hp kw from where I drove it in at. Pretty much everywhere, too. As to how much this car actually makes in Hub Dyno numbers, American Dyno numbers, or Mainline dyno numbers, I say I don't know and it's gone up ~25kw since I started tinkering lol. It IS interesting how the shorter ratio gears I have aren't scaled right on this dyno - 6840RPM is 199KMH, not 175KMH. I have also seen other printouts here with cars with less mods at much higher "kmh" for their RPM due Commodores having 3.45's or longer (!) rear diff ratios maxing out 4th gear which is the 1:1 gear on the T56. Does this matter? No, not really. The real answer is go to the strip and see what it traps, but: I guess I should have gone last Sunday...
    • GTSBoy
      What brakes on R34 GTT(Europe)

      By GTSBoy · Posted

      310mm rotors will be avilable from Australia, Japan, and probably a few other places. Nothing for the front can be put on the back.
    • MBS206
      Starting again

      By MBS206 · Posted

      The filter only filters down to a specific size. Add to that, the filter is AFTER the pump. So it means everything starts breaking your pump even if its being filtered out.
    • MBS206
      What brakes on R34 GTT(Europe)

      By MBS206 · Posted

      Just like in being 14mm too small (296mm) makes it not fit, being 14mm too big (324mm) it also won't fit. You want to find the correct rotor.
    • Kapr
      What brakes on R34 GTT(Europe)

      By Kapr · Posted

      @GTSBoy Ok so that was the shops problem...they showed R33 rotors on R34 page and i did not know 296 do not fit(and are for R33) Yes i bought "kit" with rotors and pads. Pads are ok(i have GTT calipers front and rear). They have some 324mm but no 310mm. So i dont know if they would fit. I have 17inch LMGT4s So another question. Can i fit those in the rear or they are just "too" big for that?
×
×
  • Create New...