Jump to content
SAU Community

Recommended Posts

Hey Guys,

Will be putting a new system in my R33 pretty soon and i'm not sure if my battery will be up to scratch. I'm still running the original Japanese battery, which appears it may be on its way out after spending months sitting doing nothing. It's ok and the car starts, but as I said, its the original... :uh-huh:

I'll be adding 2 amps to my system. a Clarion 400W and a Sony 222W.

I was wondering if anyone could offer advice on whether I should change my battery and if so, what type/brand of battery should I use to effectively run this system?

Link to comment
https://www.sau.com.au/forums/topic/7208-new-battery-to-run-2-amps/
Share on other sites

My stock battery seems to go fine running two amps, even when the volume is way up and I have headlights on.

If you have any doubts, install a capacitor (about $150-$300) for your amps.

But I reckon you'll be fine. I'd only change if you're not happy with the results...

Blitz33

-I think the oddyssey 1000 battery put out about 380 CCA.

They are a good battery just dont let them go flat, ie rarely run your system without the engine runing, as they die when they are drained of most of there power. They dont behave like a normal lead acid battery.

That oddyssey sounds like a monster battery, but also a monster price too...

I reckon any standard heavy duty battery of the right rating will do the trick... people run 2 amps + much more off the one battery with no probs.

Amps draw less and less power these days as well to output the same amount of wattage. More efficient components.

Guest mooks66

those amps wouldnt be pulling too much electrical draw from your system. you should be fine

just get a nice healthy 4guage power for red and black

and also upgrade your battery's ground to 4guage and also your alternator wiring to 4guage and the stocker batter will cope a heck of a lot better.

that done, your set to go

4guage into a distribution block and then 2x8 guage to the amps and your all done.

good luck

in any serious sretu i wouldnt go past and OPTIMA yellowtop deep cycle battery

950CCA 95A regular cycle and its a 95AH cell

where as the highest oddesey has to offer is a 65ah cell and the standard battery in skilines id a 45ah cell

if doing a big install the ah rating is more iportant than the CCA

and a high regular cycle can only help things along

dont forget a 100w RMS X2 amp will draw about 300W - 400W from your battery which works out to be about 30 A

im running 600w worth of amp and it draws almost 1000w from my electrical system

im using and optima yellow top and i get no dimming of the lights with all healights on

bottom line is the bigger the battery the better

Originally posted by MYGTST

in any serious sretu i wouldnt go past and OPTIMA yellowtop  deep cycle battery

950CCA  95A regular cycle and its a 95AH cell

where as the highest oddesey has to offer is a 65ah cell and the standard battery in skilines id a 45ah cell

if doing a big install the ah rating is more iportant than the CCA

and a high regular cycle can only help things along

dont forget a 100w RMS X2 amp will draw about 300W - 400W from your battery which works out to be about 30 A

im running 600w worth of amp and it draws almost 1000w from my electrical system

im using and optima yellow top and i get no dimming of the lights with all healights on

bottom line is the bigger the battery the better

I'm suprised nobody has mentioned alternators at all in this discussion.

Originally posted by MYGTST

im using and optima yellow top and i get no dimming of the lights with all healights on

How did you go fitting the Optima in the Skyline?

I am looking at a new battery for my 33 GTR as the factory one is tiny and rooted. I haven't taken all the bracing out yet so haven't sized up what I've got to work with but the options for the battery seem very limited by the size of battery you can fit in.

At the moment I am thinking of goind with the Odyssey 1000, but would much prefer the Optima/Exide if at all possible.

there is plenty of room in the back of the R33 GTR for a replacement battery, i am running the odyssey 1000 in mine, just had to make up a custom bracket to hold it down, and a little L bracket to make sure the battery doesn't move.. there is plenty of height and width available..

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for that, I'll check it all out. I can always do the brakes last anyway if its a problem.  The 16's are super cool, if they do fit I'll cruise around with them for a bit.  
    • Well, that's kinda the point. The calipers might interfere with the inside of the barrels 16" rims are only about 14" inside the barrels, which is ~350mm, and 334mm rotors only leave about 8mm outboard for the caliper before you get to 350, And.... that;s not gunna be enough. If the rims have a larger ID than that, you might sneak it in. I'd be putting a measuring stick inside the wheel and eyeballing the extra required for the caliper outboard of the rotor before committing to bolting it all on.
    • OK, so again it has been a bit of a break but it was around researching what had been done since I didn't have access to Neil's records and not everything is obvious without pulling stuff apart. Happily the guy who assembled the engine had kept reasonable records, so we now know the final spec is: Bottom end: Standard block and crank Ross 86.5mm forgies, 9:1 compression Spool forged rods Standard main bolts Oil pump Spool billet gears in standard housing Aeroflow extended and baffled sump Head Freshly rebuilt standard head with new 80lb valve springs Mild porting/port match Head oil feed restrictor VCT disabled Tighe 805C reground cams (255 duration, 8.93 lift)  Adjustable cam gears on inlet/exhaust Standard head bolts, gasket not confirmed but assumed MLS External 555cc Nismo injectors Z32 AFM Bosch 023 Intank fuel pump Garret 2871 (factory housings and manifold) Hypertune FFP plenum with standard throttle   Time to book in a trip to Unigroup
    • I forgot about my shiny new plates!
    • Well, apparently they do fit, however this wont be a problem if not because the car will be stationary while i do the suspension work. I was just going to use the 16's to roll the old girl around if I needed to. I just need to get the E90 back on the road first. Yes! I'm a believer! 🙌 So, I contacted them because the site kinda sucks and I was really confused about what I'd need. They put together a package for me and because I was spraying all the seat surfaces and not doing spot fixes I decided not to send them a headrest to colour match, I just used their colour on file (and it was spot on).  I got some heavy duty cleaner, 1L of colour, a small bottle of dye hardener and a small bottle of the dye top coat. I also got a spray gun as I needed a larger nozzle than the gun I had and it was only $40 extra. From memory the total was ~$450 ish. Its not cheap but the result is awesome. They did add repair bits and pieces to the quote originally and the cost came down significantly when I said I didn't need any repair products. I did it over a weekend. The only issues I had were my own; I forgot to mix the hardener into the dye two coats but I had enough dye for 2 more coats with the hardener. I also just used up all the dye because why not and i rushed the last coat which gave me some runs. Thankfully the runs are under the headrests. The gun pattern wasn't great, very round and would have been better if it was a line. It made it a little tricky to get consistent coverage and I think having done the extra coats probably helped conceal any coverage issues. I contacted them again a few months later so I could get our X5 done (who the f**k thought white leather was a good idea for a family car?!) and they said they had some training to do in Sydney and I could get a reduced rate on the leather fix in the X5 if I let them demo their product on our car. So I agreed. When I took Bec in the E39 to pick it up, I showed them the job I'd done in my car and they were all (students included) really impressed. Note that they said the runs I created could be fixed easily at the time with a brush or an air compressor gun. So, now with the two cars done I can absolutely recommend Colourlock.  I'll take pics of both interiors and create a new thread.
×
×
  • Create New...