Jump to content
SAU Community

Recommended Posts

3. My car has been legally registered in the state of NSW with the exhaust on it.

So what... how many pac cars do you see with numberplates on them. The RTA do not test a cars emissions in order to pass registration. If you tell the court that it was registered they wont care.

Focus on those other points you had. Those are good.

Spend some time on austlii looking up the various laws and get familiar with them.

  • Replies 45
  • Created
  • Last Reply

Top Posters In This Topic

The RTA do not test a cars emissions in order to pass registration. If you tell the court that it was registered they wont care.

I know they dont, but my car needed to be blue slipped in order for it to be re-registered, and they would not give me a blue slip without an engineering certificate.

Jax - Thanks heaps. PM replied.

  • 1 month later...
Hey guys,

Need some advice, legal or not, about a fine I received today just near Armidale. I was pulled over by a highway patrol car about 5 minutes east of Armidale (on my way back to Coffs Harbour). After a breath test, the officer informed me that he was not satisfied with the cannon (HKS Super Dragger) which was installed on my car.

I proceded to inform him that I have an engineer's certificate for the exhaust and that it was under the 90db limit. He informed me that he was not interested in the certificate because the law that he was fining me under was an EPA noise regulation. I also offered to show him my last defect for my exhaust which states as a requirement for the defect to be cleared:

"All modifications and components to comply with EPA and RTA regulations"

This was signed by a Sergeant of the local highway patrol here in Coffs, and the defect was cleared.

Basically he informed me that (and he showed me the act that was in question, I wish I had taken note of it), a car must not be fitted with a noise control system that is different to the one that was fitted from the factory. He said that he would not defect me, but if he saw me again with an exhaust that is not factory, he would fine me again, and again, until I revert the exhaust back to standard.

Now I'm seriously thinking about taking this to court as the fine is $200 and I will no doubt lose some valuable points off my license. On top of that I seriously want answers as to why, after spending almost $800 getting my car engineered to ADR standards, I can still get fined!!

Any thoughts or suggestions from people who are in the know or have contested fines before would be greatly appreciated. Please keep replies as helpful as possible.

Thanks in advance. :)

Just wondering if you had your day in court? what happen? any updates?

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • would a r34 gtr hood line up with gt/gtt stock fenders? after latch, front bumper and hinges are swapped for gtr ones? or would the fenders be too low or high in relation to the hood surface? ( I believe seeing somewhere that gtr front fenders use some type of riser for the sides, but do not know how that relates to stock gt/gtt fenders.)    
    • You just need to remove the compressor housing, not the entire turbo. I would not be drilling and tapping anything with the housing still on anyways. 
    • So, I put my boat on a boat. First of all, I'm going to come out and say it. Why is Tasmania not considered a holy goal, an apex that all road-legal modified cars go to, to experience? This place is an absolute wonderland of titanic proportions. If people are already getting club runs for once in a lifetime 30 person cruises to Tassy then I've never seemed to see it. It is like someone replaced the entire place with an idyllic wonderland for cars, and all of the people living there with paid actors who are kind, humble, and friendly. Dear god. After doing a lap of almost all of the place I've found that it's a great way to find out all of the little things that the car isn't doing quite right and a great way to figure it all out. All in all, I drove for 4 hours a day for a week and nothing broke. I didn't even need to open the engine bay. This is by all means a great success, but it has left me with a list of things to potentially address. I also now have a 3D printed wheel fitment tool which annoyingly hasn't got any threads in it to actually assemble it. I might be able to tape it together to check the sizing I actually want to use, but it'll likely involving pulling the shocks out to properly measure travel at least at the front, and probably raise the car while I'm at it, at least in the rear. I scraped on quite a few things and I'm not sure how else to go about it. I was taking anything with a bump at what felt like 89 degree angles. And address those 10 other tasks. And wash the car. God damn it is dirty. And somehow, the weather was perfect the entire time - And because I was on the top of Mt Wellington it turns out it was very much about to freeze up there. I did something I typically never do and took some photos up there in what must have been -10 and the foggy felt like suspended ice, rather than mere fog. If you own a car in Australia, you owe it to yourself to do it.
    • Damn that was hilarious, and a bit embarrassing for skylines in general 😂 vintage car life ey. That R33 really stomped. Pretty entertaining stuff
    • Hi, I have a r32 gtr transmission. Does any of you guys have an idea how much power it will hold with the billet center plate and stock gearset? At what power level and use did yours brake with or without billet plate? Thanks, Oystein Lovik
×
×
  • Create New...