Jump to content
SAU Community

Recommended Posts

  • Replies 214
  • Created
  • Last Reply

Top Posters In This Topic

Ok.

Everyone who chose to deposit 50% now 50% later. It's later.

Same as before deposit the rest of the money and email me receipt.

Thanks guys.

Also,

Some notes from WSID

1.Two drivers to one car: No problem. But both drivers MUST present themselves at the same time for credentials. It won’t be permitted as an “afterthought”. There will not be any change to the pricing structure.

2.Track preparation: The track will be prepared at least to Street Meet level. That means the track will be spayed for the first 60-80 feet and have the tyre machine dragged over it for two-plus hours.

3.Burnout Pad access: No; can’t do this for you. As explained earlier, this activity changes the sanction fee considerably which would need to be added to your track hire fee. It doesn’t matter how briefly someone may wish to use it.

4. seating: Please advise your people that no one is permitted into the gold seating area. The adjacent grass-terraced area at the north-western corner of the spectator area is an excellent area that provides an overall view of the venue. Perhaps you could suggest that people bring a blanket and/or cushions for their comfort.

Ok

 

  3.Burnout Pad  access: No; can’t do this for you. As explained earlier, this activity changes the sanction fee considerably which would need to be added to your track hire fee. It doesn’t matter how briefly someone may wish to use it.

 

t]

dam!!!!

is there a rule about burnouts on the strip?

for example if i want to over excesively warm up my tyres?

I would imagine that this would be ok provided it wasn't to continue for minutes, ie your still sitting there warming up your tyres and the other bloke is complaining as his have gone cold.




  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...