Jump to content
SAU Community

Recommended Posts

I'll start by saying I know sfa about car audio so please excuse me if i ask stupid questions.

I have the following:

- jvc mp3 h/u

- mb quart splits

- signat 2 channel amp (2x60watt rms)

- pioneer 2 ways for rear fill (run off h/u)

- 10" mtx sub (will run 100 - 200 watts rms)

I need another amp to run my sub, my options are:

- buy another 2 channel and run two amps

- sell my current amp and buy a 4 channel

Will running two amps drain my battery of power so I won't be able to listen to my system for very long with the engine off? Will I need to upgrade the alternator or anything else?

Thanks for you help! :P

Cheers,

Greg

Link to comment
https://www.sau.com.au/forums/topic/7331-your-advice-wanted-please/
Share on other sites

Running another amp = more power = more current drain. So in short, yes.

Depending on how good your charging system is you shouldn't need to upgrade your alternator. You might also want to consider investing in a capacitor - not essential, but will help "smooth" the current flow to the amps.

Why not purchase a 4 channel to run the speakers & bridge the sub of the 2 channel? By running fronts off an amp and rears off the head unit you will probably find that the rears won't have enough volume.

  • 3 weeks later...

to starr with...amps are designed to run when the car is running...ie. 14.something volts, not 12! so running it when the car is turned off isnt that good. but ive found if the amps arnt staining for power (not enough power for the speakers) it doesnt do much harm (well, noticably)

if you are only going to be running a set of splits and only 1 sub, i wouldnt worry about a capacitor, just upgrade your battery perhaps.

amp wise, a 4 channel amp would do the trick...2 for the fronts and bridge the other 2 for the sub. alternativly, you could get another 2 channel amp, depending on where you are going to mount them and how much room you want left. remember, amps are generally designed to get rid of the heat when they are sitting normally...so if you mount it upsidedown and its being put to its full potential, you might have an over heating problem and then bye bye amp!

hope this helps, hope i didnt sipn too much crap!

  • 3 weeks later...

thanks all for your replies :D

i've decided i don't want to spend money on another amp just yet...so here are my options:

a) Use the amp to run my splits, and run no sub for the moment

B) Use the amp to run my sub and run splits from the head unit

I'm leaning towards (a) because my splits were pretty expensive and are quite good quality so it would be a waste not running them off an amp.

what do you think?

Yup, subbies require more power to generate a decent volume.

Hence why most subbies are around 1000w and you will not find much above 300w for other speakers. Really for a sub, an amp is essential whereas for splits its not.

I hooked up my splits to the amp but it lacked bass... so then i hooked up the sub to the amp and ran the splits from the head unit. It sounds sweet :D

I might get a cheap 2 channel amp to run my splits though because the sound is so much clearer with an amp. Anyone know of any amps for sale?

Thanks for your help all

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...