Jump to content
SAU Community

Recommended Posts

hey all

just replaced my exhaust manifold gasket, put it back together and now the thing wont idle and is producing a crap load of black smoke. the thing is last nite after it was all back together i started it up and it ran fine, but when came to moving it this morn it wont run. i also had a flat battery this morn so when trying to kick it over could it of damaged the ecu in any way?

ive pulled all the pipes off again checking if they were restricted but they were clear. do airflow sensors just pack it in? as this is the only other thing i can think of.

any help would be much appreciated

Link to comment
https://www.sau.com.au/forums/topic/73624-a-lot-of-black-smoke/
Share on other sites

Is it black, or grey? Where is it coming from: exhaust tip or engine bay?

When I replaced the exahust manifold, turbo-to-dump, turbo-to-manfold, and dump-to-front gaskets my R32 GT-R was pumping grey smoke like something was on fire :P After about 30 minutes of idleing, the gaskets finally started to seal and the smoke disappeared.

The idle was a bit high, but was fine otherwise. I had to replace my sparkies the next day as they became fouled, I assume from a combination of (normally) rich running plus screwed A/F ratios due to the exhaust leak, and the 30 minutes it took for things to seal up.

Lucien.

Black smoke and not running probably means you didn't connect up a cooler pipe properly when putting everything back together.

AFM sees lots of air so gives the engine lots of fuel. Engine sees little air so pumps the fuel out the back in the form of black smoke and backfires until it floods and stalls.

cheers for all the replies. its all sweet now though. went through and reconnected everything( intercooler pipes, pod assembly) and the thing was still running rough, but after a bout an hour of trying it started, ran rough for bout a min then just kicked in, although it has a bit of a miss now though. time for a full tune me thinks.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Join SAU NSW for a flame-grilled feed & flame-spitting cruise! Sunday 17th August 2025 3:30PM Meeting Archies Flame Grille Sylvania Waters 4:45PM Cruise Departure 5:15PM Arrival at Cape Solander Kurnell Meet Location: Archies Flame Grille Final Destination: Cape Solander Kurnell *Disclaimer* There will be a lead and follow car so no one should get lost. If you would like to attend or bring others along please put your name down and a +1 as numbers will be needed prior! This is NOT a race and we will all be adhering to all road rules. If this is what you want please come to one of our many track days. This is an official SAU:NSW event and will be run under a CAMS permit. One of the things that really sets our club apart is our commitment to being true enthusiasts. When on normal roads we strive to maintain good relations with the authorities as well as the public in general. When attending one of Skylines Australia NSW events please try to: • Be aware of surrounding environment and act accordingly. • Drive courteously on the state’s roads as a true enthusiast should. • Understand how important it is to maintain the good name of SAU NSW and thus, treat others accordingly. • Any misbehavior will not be tolerated and you will be asked to leave.
    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
×
×
  • Create New...