Jump to content
SAU Community

Recommended Posts

Unless you have a CAI or a heatshield of some sort, installing ANY pod filter will more than likely decrease your power (due to the hot air generated by engine being sucked up by the pod).

So with that in mind, changing to a brand name pod will do nearly nothing to increase performance.

You can make your own with just some sheet metal. Just make sure you find a good way to secure it.

If you have a R33 there's a groupbuy for this heatshield+pod setup:

http://www.skylinesaustralia.com/forums/sh...ead.php?t=47767

Or this airbox for R33/34:

http://www.skylinesaustralia.com/forums/sh...ead.php?t=57642

thats what i was wondering, doesnt it get messy??

also dont use an oiled pod such as k and n to reduce risk of covering the AFM with oil. probably best to use a dry one such as an apexi.

if u have a dry one on there that looks like it filters ok just leave it or partition it.

hey..

If you in melbourne I believe its illegal to use the pod oiled type (k&n etc etc) unless its in a box..

Apparantly the Apexi ones (there non oil) are fine though.. because of the no-oil factor...

Get a k&n panel filter and stick that in the stock airbox.. thats the best way to go..... unless you do the CAI in the front bumper, if not you'll just be hearing the stupid sucking noise everytime you drive and wondering if its actualy doing anything good for your car :rofl:

cyas

Although my pod is in the guard, its not so low that there is a risk of sucking up water from puddles etc. Besides the fact that i dont really drive my car in the rain (its a second car) im not gonna drive thru cause ways etc; although one of my friends did this during a flood and hydrauliced his engine; blew a hole in his block. Also, i like the fact that its hidden ans with some cops its 'out of sight, out of mind'. Im using a MAP sensor too, so i dont have to worry about AFM's. Also, keep in mind that a tiny amount of water splashing in from rain wouldnt really hurt anything, as some people set up water injection into the engine to keep combustion temperatures low. Thats just my opinion; correct me if im wrong.

Shaun.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • 9" wheels are a little too wide for a RWD 32. They can fit. People have put R33 GTR wheels on 32s for years and years. But they are a very tight squeeze. This has been known for about 30 years. As I said - there is no difference between a 17 and an 18 in terms of what will fit. The rolling diameter needs to stay about the same as stock - not very much larger. If you increase that, you will start to have problems. If you increae rolling diamater at the same time as yo increase width, you will have problems earlier. as 9" wheels are pushing the boundaries already, you would need to be careful with tyre choice. I would put 8.5s on the front of mine, but would expect problems with 9s.
    • post up screen shots of your injector tables
    • Diagnostic flow for a code 21 says check signal at the ECU pins, on a voltmeter of some kind it should read 0.1V at idle, 0.12V cranking, 0.15-0.25V at 2000 rpm. Check each coil such that +1, -3 is infinite or very high resistance, -3, +2 should do the same. (-1, +3), (+3, -2), (+1, -2), and (-1, +2) should all be somewhere between 0 ohms and high resistance. If you trace the path from the coil pin all the way back to the ECU in the diagram the resistance you measure at the coil vs connected to the harness should be pretty much the same. 
    • I have an elite 2500 running an adapter harness on an rb25de neo r34. I took the butterfly out and removed all that junk. But I also went Plus+t at the same time. The butterfly thing works in reverse to the boost solenoid on the Gtt if that makes sense
    • yeh they are 235/45/17 up front and 255/40/17 in the rears. I still didn't get my answer if i can fit a 18x9 up front. I want to get 4 of this and see if they will fit before committing as they didn't see an 18x8 as an option but there is a 18x9.5 also.   Enkei RS05-RR 18x9 35mm ET 5x114.3 75.0 Bore Matte Gunmetal Wheel
×
×
  • Create New...