Jump to content
SAU Community

  

24 members have voted

You do not have permission to vote in this poll, or see the poll results. Please sign in or register to vote in this poll.

Recommended Posts

Guys/girls,

could i get an indication if any here who would be up for a nice drive/cruise this coming weekend either on the fri/sat or sunday. Some memebers on msn have asked if one could be organised and i said that i would see if there is any interest.

post up your opinion,

duc.

p.s. it has been so long and it would be great if we can get a shot of all the cars and its members from sau - sa.

Update

The route will consist of locations/roads such as mt lofty summit, eagle on the hill and handorf. No roads on the streets will be disclosed.

Meeting location will be pm'd to those on the list of attendees. Likewise the route. Ill bring some directions on the day too just in case anyone would like one.

Time

meet 2:00

departure 2:30

list of attendee's

sam

nozila

ghostdog

oosh

chillam

boosted 32 girl

lukew105

whatisname

writeoff

nismotsu

blu32

nightcrawler

nissangts

skidline

premo

iceduck

gtrob

  • Replies 122
  • Created
  • Last Reply

Top Posters In This Topic

I don't make it back till the prolli the 30th.. but ifanything is on for the following week there.. I'd go for sure..

There is a NS.com cruise on the 3rd .. but it is open..I'd rather have ppl that respect their cars on a Cruise.. but if not.. I'll go anyways..lol.

I only got 1 week back in adelaide..

So It'd be cool to meet you guys

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Similar Content

  • Latest Posts

    • The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Good luck on the weekend mate
    • Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Welcome to SAU, what are you looking at buying?
    • I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...