Jump to content
SAU Community

Recommended Posts

Finally run a half reasonable time

12.1 @ 111mph

but i have a question... last time with 200rwkw i ran a 12.90 with 200rwkw or there abouts.

now im up around the 300rwkw.

My time has gone almost a second up, yet my MPH hasnt changed one skeric really. Any ideas why that is?

I made a nice 1.90ft, same as my old 12.9 run was.

So they were pretty similar, jsut the times changed :headspin:

Link to comment
https://www.sau.com.au/forums/topic/75175-finally-a-decent-time-and-a-q/
Share on other sites

At Heathcote i was running 12.7@111 and i have around the 235rwkw mark. What was your half track speed? Should be around 87mph. Something sounds a miss even with a 1.9 60'. Are you sure you werent shutting down just before the line, Ive done that before.

What mph was your 12.9?

12.1@111mph you must be getting of the line pretty quick!, i only ran 12.4@112mph when i went - and i have 4wd launch!

oops, it was 109mph, and id run 110/111 just for times of 13.00/13.10 etc

my 660ft times was 9.3/80.7 mph... i wasnt backing off thats for sure.

I kept my foot in right past the little white checkers :rofl:

i went easy on the launch as the cars just burns the tyres if i try a decent one

my 660ft times was  9.3/80.7 mph... i wasnt backing off thats for sure.

I kept my foot in right past the little white checkers  :rofl:

i went easy on the launch as the cars just burns the tyres if i try a decent one

There is something wrong with that 660' time, your at least 1.0 off the pace and 8mph. Check it with your other runs at the 660' mark.

correction, stoopid a$$ me looknig at the wrong sheet

660ft was 8.00

mph/660 was 94.8=68

It has way more than it did wheni ran a 12.9, i seriosuly doubt there was another second in there back in its old form. I've changed nothing traction wise at all.

If anything the tyres are a bit older and crappier now than they were a year ago (12.9 @109mph/200rwkw)

I know the problem. :P

Well m yguess anyway is that the clutch was starting to struggle in the top gears, and what you though may have been wheelspin into 2nd nd maybe into 3rd was actually the clutch starting to give up...well perhaps a combination of both.

That night at Clader where you chopped me my clutch was getting worse with every run, by the end of th enight my mph had dropped 3-4mph when only running approx 200rwkws.

Anyway food for thought:)

with the power you claim your trap speed is way down might be an idea to run it up on a dyno just to double check maybe you have a problem ?. Your abit slow to the 660ft mark and you mph is down thing is your 60ft times aren't bad at all .

For whats it's worth I know my car is abit of a differen't kettle of fish but I have one of the slips here for a [email protected] and on that run went

660ft 7.837@91mph with a 1.8 60ft .

Also don't be fooled into thinking peak power dyno read outs are everything can you tell us abit more about the car and mods .

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Pressure when IDLING, is meant to be 51PSi... So that amperage value needs to go up a fair chunk... I'd personally be factoring for more like 12amp at least on those runs, and at that point you need to hope the already there wiring doesn't drop you a volt or two, as that's a lot of fuel pressure flow drop off from 13.5 to 12V! Taking idle pressure of 51psi, means the pump will be drawing a MINIMUM of 9amps all the time based on your reading of the graph (3bar base, then allowing an extra 0.5bar for boost = roughly 51psi)
    • Hi all,  I am in the market for an R200 longnose diff out of a Z31 300ZX, or S12 RSX, DR30 skyline, or similar, in a 3.9 ratio.  Preferably a late model one with the M12 crownwheel bolts.  The only easy to find advert for one of these was my ad back in 2007 when I sold it on this forum.  I sold the diff as I had sold the car it goes to, but as it turns out, after 18 years I got the car back late last year, so now I'm looking for the diff !  If anyone knows where to find a longnose R200 LSD with the M12 crownwheel bolts, drop me a line at [email protected] - Bonus paid if soomeone comes up with the original diff (stranger things have happened !).  Cheers   Ben D    
    • Hi everyone, I used to post here a bit from 2004-2013, when I owned various Nissans, in particular my S12 RSX gazelle, which was sold in 2007.  As luck would have it, after an 18 year hiatus, the car found its way back to me last year, and over the past 11 months I have had the pleasure of restoring it with my kids.  One thing that I am after in particular is a 3.9 ratio R200 LSD for it.  I actually sold the one out of the car here back in 2007 , and it would be incredible if I could track down who I sold it to, so I can see how they have progressed over the years (and to be honest, to see whether I can get the diff back !).  Anyways, hi all and let me know "where are the R200 Longnose diffs all at these days ?  Cheers Ben D  
    • Arms will be the same as the G35 or 350Z, but as above, there was a change in the lower control arm where it connects to the ball joint.  That said, you can remove the ball joint cone from your old ball joints and fit them to the new ball joints.  To be honest, I didn't think the ball joints themselves were different. The main ball joint is a bit awkward to replace, you really need to remove the steering knuckle to press out the old one.  Some people have used tools to remove it in place, but it just seemed too hard to get to. If you are going to press out/in that ball joint, then you may as well just replace the bushings in the LCA and the compression rod.  You can buy the compression rod bushing from Nissan, but the LCA bushes, you will need to go aftermarket. Much cheaper than buying the whole arm.
    • Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
×
×
  • Create New...