Jump to content
SAU Community

Recommended Posts

http://www.mgccsa.org.au/vintagec.htm

Also, check the 'Hill Climb Sup Regs' PDF link on the left menu for more info.

I think the address is:

Collingrove Hill Climb

Lot 100, Hill Climb Road

Angaston Rural

This is where the WRX club use to have one of their track events, wish SA had an official SAU club.

Hillclimb - cool! I opened the Hillclimb Pdf, that indicates the Hillclimb to be on the following weekend 12 June 2005.. is that a second climb or the actual date? Let us know as I'm quite keen too

oops sorry, didnt check the dates there. The one 'jager' was referring to is this one - http://www.nissansilvia.com/forums/index.p...showtopic=91758

The track is 7kms SE of Angaston on the Angaston to Eden Valley Rd, if you get lost Im sure the locals in the Barossa can direct you.

OK, from town the easiest way is as follows.

1. Go straight up Main North Road

2. Go around the Gawler Bypass and keep heading along the Sturt Highway towards Nuriootpa.

3. You will come to a fairly major turn off to Tanunda on your RIGHT, via Gomersal Road (possibly Highway). Take this all the way to the end.

4. At the end turn LEFT onto the main street of Tanunda.

5. Continue down the street through Tanunda untill you come to a S-bend/railway crossing and turn RIGHT at the SECOND Road. (you want the one that is almost directly ahead, not the one back towards Tanunda)

6. Follow this road for a while ignore the first sign to Angaston(I've oly been that way at night so i don't really know it.) go over a train crossing and past the VINPAC factory on your right.

7. You will come to a cross intersection with a sign saying Angaston to the RIGHT , follow that. This will take you up the Main street.

8. When you reach the end of the main street you must turn RIGHT.

9. Follow this road past the Collingrove Homested, keep going untill you see a sign for the Collingrove Hillclimb on the left. Turn down the dirt road immediatly after the sign.

The gate to get in, is on the left, By this time you should have a pretty good idea of what's going on!

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • I've been doing some looking around and honestly was just considering throwing a new rack at it. I saw that the dmax silvia rack bolts up into the 33 with the silvia bushings but not sure if the high pressure lines will sit in the correct spot. I believe other version of the 33 rack are the same/similar to the racks that can be opened up without as much fuss so I assume the dmax rack would fit but any ideas?
    • I've never played with one, but I would expect that you are correct. That slot looks like it is intended to be used to unscrew the end, and the flats on the body would be better than grabbing it around the round bit with a pipe wrench. So, yeah, probably unscrews. You'll probably have to make a tool to drive in that slot.
    • A bit late but A disk S13P fit over stock R32 GTR brakes, usually A disk front, O disk rear works.
    • Or, the height of the release bearing is not correct for your combo. Start with the bleeding and checking the slave moves throughout its range when you press the pedal (2 person required), but it is possible for the height to be internally wrong too (box back off to measure.
    • Yes, there's quite a few things that can go wrong during a clutch install. Very unlikely. I have a similar clutch. They (ACS) make good gear. No, it is not normal. It is possible that you just need to bleed the clutch slave. But the new clutch will also have a more aggressive actuation force/pressure, and so your old slave cylinder might be a bit leaky or otherwise compromised, and not up to the extra force required. Or the master cylinder, same.
×
×
  • Create New...