Jump to content
SAU Community

Recommended Posts

89 model r32gts-t

8x.xxx

black

manual

sony cd deck

pioneer 6" 4 ways in door's has wiring for sub and amp, but was taken from car

3.5' turbo back kakimoto exhaust

r34 wing

k&n pod filter

bov plate(just put it in)

exelent interior no holes from bolt on's in interior and one of the best interior's you will see for an 89 model r32, car runs very well, engine is exelent, only been boosted to 12psi for 10,000km, has new fuel filter and a few lil other things ive fixed.

*** the car needs a blue slip, as it was registered in qld and i moved to nsw, has stock bov, and air box to pass no worries, i was looking for a trade, before but problems came up with my liscence, and not much point keeping my car, so yeh dont really want to let go of her but ill be taking offers at 12,000

gtst1.jpg

gtst3.jpg

gtst4.jpg

gtst9.jpg

nemzr32engine.jpg

Link to comment
https://www.sau.com.au/forums/topic/75388-syd-r32-gtst-manual-black-89-12k/
Share on other sites

  • 2 weeks later...
  • 2 weeks later...

reply's sent, i wont go any lower then this, the car is very clean, the body is a little rough, but only minor things, the interior is the best ive seen, and suspension, gear box, engine is all tight, feels very good to drive, seriously first to drive it will buy it, it hasnt been thrashed and u can feel it when u drive it and when u look at it inside, its very well taken care of

  • 3 weeks later...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah good luck out there! Will be good to see a mighty GTST going harder than the GTRs
    • i will be there 😁
    • Hello!  i just finished manual swaping my r34 skyline with a r33 rb20de box(RB71C)box  When the car is running it squeaks crazy loud and it was smoking from the gearbox area. The gearbox is fine it was tested. The clutch slave cylinder seems like it doesn't fully releases the clutch. I want to ask if this noise is from the throw out bearing or could it be the clutch assembly or disk att.xFliq87Gzw6kImKBVqDebXkj0fBqymk0JaYeP3_3SlM.mp4
    • A few small updates since the previous post and lessons. I decided to do a little interior light upgrade on the 110. I quite like the iilumo items, even if they're a bit of a premium over other brands. You'll also note the Stedi Fogs, that will go into the S15 fog lights as I needed to match the bulbs since I got the new ones earlier. I hope they fit as the body is quite a bit longer than your normal bulb.  Annoyingly, I managed to trip the fuse, which normally wouldn't be an issue until I located the fuse. I can't say I've ever come across this. I had lucked out that someone nearby had a spare, but oddly enough Toyota dealerships seem to keep this in stock. I ordered some to keep in my stash and as luck would have it, someone else nearby tripped the same fuse so I passed on the favour.  I also did a little service on the 110 ahead of some additional work coming up. It's been annoying that Goleby's stopped carrying this particular HKS filter for the 110, so now I need to keep them on order from Japan. I also took the opportunity to install a bash plate and number plate riser. The plate riser is such a cheap but nice fix to help really tidy up the car. I'm tempted to now also replace my headlights, on this car. Both items were from Project Aero.    I also needed to replace the rear tyres on the 110, and after trying to get it aligned learnt that I need to replace some bushes in the front end, so that's next.  Closing out this update with a nicer picture as always! 
    • Yeah mate, never miss it.
×
×
  • Create New...