Jump to content
SAU Community

Recommended Posts

hi there guys im obviously new to this forum and am looking for a few tips on what to look out for when buying a r32 gts-t....im after a manual, preferably one that is already registered here.

im after common problems (if any) that i should be wary of, or just some general advice on what to keep an eye out for?

thanks for the help.

Link to comment
https://www.sau.com.au/forums/topic/75668-buying-a-r32-gts-t/
Share on other sites

Just the things you'd check any car for really, accident repair that sorta thing. Try and get it leakdown tested before you buy too, as this will be a good indicator of engine health. Most of the age related problems with my car were very easily fixed (leaky ball joints and so forth). There are a few guides here (wish I could link ya) that go into detail about looking over a car that you should definately read.

I’d be looking for the following:

Rust

Workmanship of the mods if any.

Accident damage

The noise from the turbo

Clutch slipping

Rpm at Idle

Where the car gets serviced

The owner themselves. Do they look like the kind of person that looks after their cars!

Hey I’m about to get a work car and have a mint condition 1992 R32 with:

Aftermarket injectors

Aftermarket fuel pump

Highflowed RB25 turbo

Fully tuned Apexi AFC

Heavy duty clutch

And heaps of other extras,

Drop me an email if you’re interested as I haven’t put it on the market just yet but planned on selling it at the end of June.

Honestly if I got 11k for her I’d take it as I cant be bothered f%cking around for months to get 13-14k

[email protected]

R32 - one of the nicest cars, couldnt recommend one more for a person getting into the Import scene - the styling is timeless..

I regularly have dreams of a nice lowered black 32 with the type M front bar......hang on that was my old car :)

Nah but seriously, R32s are awesome cars, provided you service regularly and dont wring the neck outta it all the time.

many have had the shit beaten out of them so look for replaced engine parts, unusual sounds, lacking appropriate power, any special starting procedures (a few of the cars i checked in my search for the perfect r32, you'd have to pump the accelerator to start it, heh) etc

you'd be smart to have an expert check it over. only 2 cars passed my own inspection. one when checked out by my engineer was junk (he picked up on very subtle problems i would never have notice - hydraulic lifters, quality respray of a panel, and a replaced brake caliper indicating a possible whack in the rear right). the 2nd one was bought.

pm me if you'd like his number :)

also, the hicas warning light in many of the cars comes up which is a pain. the car you buy will probably depend on your patience and whether you're a perfectionist or not, among the other obvious things.

check the heater some of them are stuffed an they make a sound when changing from head too feet

an check wheels to see if they are toed or out of place .....cos the car might have drift damage (hard to see,not cheap to fix)

thats what happend to my old r32......

i know, big change!!!

lol good change ;)

check for kinks in the rails in the engine bay or any creases in the structural parts of the car... like around the strut towers. Obviously there are a lot of creases and so forth there normally, but its should be pretty much symetrical so check both sides... if ones different to the other look into it.

-HICAS light is normally due to aftermarket steering wheels. If its a stock wheel it could have a HICAS stop kit on it so check that

-Air Con make sure it works. If it doesnt and it has an aftermarket stereo or gauges it could be because the facia was taken off and put back on wrong crimping the hose that helps measure the temp in the car OR of course it just needs some good ol gas :rofl: The noise switching from head to feet is usually the vent redirecting the air and isnt really an issue.

-Boot rust. Places they seem to be prone to rust are the bottom of the rear gaurds near the back of the wheel arches and inside the boot near that same area. you actually need to lift up the carpet and feel down the inside.

Apart from that, just the usual shit... dont get RACV to check it out they wont know what theyre looking at and like to charge 4x the amount to look at them.

Hey Buddy,

Good choice of car to look at!

If you are seriously looking to buy one, my mate is selling his. 93' charcoal grey, i/c, nice fat rims, kit, exhaust, brass button, etc,etc... beautiful car but more importantly properly cared for. He is in the eastern burbs of melb.

Pm me for details.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • If as it's stalling, the fuel pressure rises, it's saying there's less vacuum in the intake manifold. This is pretty typical of an engine that is slowing down.   While typically is agree it sounds fuel related, it really sounds fuel/air mixture related. Since the whole system has been refurbished, including injectors, pump, etc, it's likely we've altered how well the system is delivering fuel. If someone before you has messed with the IACV because it needed fiddling with as the fuel system was dieing out, we need to readjust it back. Getting things back to factory spec everywhere, is what's going to help the entire system. So if it idles at 400rpm with no IACV, that needs raising. Getting factory air flow back to normal will help us get everything back in spec, and likely help chase down any other issues. Back on IACV, if the base idle (no IACV plugged in) is too far out, it's a lot harder for the ECU to control idle. The IACV duty cycle causes non linear variations in reality. When I've tuned the idle valves in the past, you need to keep it in a relatively narrow window on aftermarket ecus to stop them doing wild dances. It also means if your base idle is too low, the valve needs to open too much, and then the smallest % change ends up being a huge variation.
    • I guess one thing that might be wrong is the manifold pressure.  It is a constant -5.9 and never moves even under 100% throttle and load.  I would expect it to atleast go to 0 correct?  It's doing this with the OEM MAP as well as the ECU vacuum sensor. When trying to tune the base map under load the crosshairs only climb vertically with RPM, but always in the -5.9 column.
    • AHHHH gotchaa, I'll do that once I am home again. I tried doing the harness with the multimeter but it seems the car needed a jump, there was no power when it was in the "ON" position. Not sure if I should use car battery jump starter or if its because the stuff that has been disconnect the car just does send power.
    • As far as I can tell I have everything properly set in the Haltech software for engine size, injector data, all sensors seem to be reporting proper numbers.  If I change any injector details it doesnt run right.    Changing the base map is having the biggest change in response, im not sure how people are saying it doesnt really matter.  I'm guessing under normal conditions the ECU is able to self adjust and keep everything smooth.   Right now my best performance is happening by lowering the base map just enough to where the ECU us doing short term cut of about 45% to reach the target Lambda of 14.7.  That way when I start putting load on it still has high enough fuel map to not be so lean.  After 2500 rpm I raised the base map to what would be really rich at no load, but still helps with the lean spots on load.  I figure I don't have much reason to be above 2500rpm with no load.  When watching other videos it seems their target is reached much faster than mine.  Mine takes forever to adjust and reach the target. My next few days will be spent making sure timing is good, it was running fine before doing the ECU and DBW swap, but want to verify.  I'll also probably swap in the new injectors I bought as well as a walbro 255 pump.  
    • It would be different if the sealant hadn't started to peel up with gaps in the glue about ~6cm and bigger in some areas. I would much prefer not having to do the work take them off the car . However, the filler the owner put in the roof rack mount cavities has shrunk and begun to crack on the rail delete panels. I cant trust that to hold off moisture ingress especially where I live. Not only that but I have faded paint on as well as on either side of these panels, so they would need to come off to give the roofline a proper respray. My goal is to get in there and put a healthy amount of epoxy instead of panel filler/bog and potentially skin with carbon fiber. I have 2 spare rolls from an old motorcycle fairing project from a few years back and I think it'd be a nice touch on a black stag.  I've seen some threads where people replace their roof rack delete with a welded in sheet metal part. But has anyone re-worked the roof rails themselves? It seems like there is a lot of volume there to add in some threads and maybe a keyway for a quick(er) release roof rack system. Not afraid to mill something out if I have to. It would be cool to have a cross bar only setup. That way I can keep the sleek roofline that would accept a couple bolts to gain back that extra utility  3D print some snazzy covers to hide the threaded section to be thorough and keep things covered when not using the rack. 
×
×
  • Create New...