Jump to content
SAU Community

Recommended Posts

I thought a stealth bov was black and inconspicuous looking rather than quiet so that during inspections by cops they can't see that it's different.  I may be wrong though.

As advised, they come in silver and other colours. The "stealth" part is the ability to basically turn them off.

You can adjust how much plumb back and the pressure this occurs from memory.

Now, if only I could be bothered to open the bonnet and turn it down every time I drive it (My Wife likes to make a little noise).

Enjoy!

El Bee (I must be getting old eh)

I have the stealth bov on my r33. Its really good because you can control how loud you want the bov to be. You can also take the trumpet off it looks less suspicious if you do have it vented to atmosphere. But if you have the trumpet on and you have the bov on plumb back, the cops still pick at it as they think it on vent to atmosphere.

So the sound travels through the pod.Im guessing it is very faint compared to my blitz supersound bov.

I really feel like driving a car that doesnt draw the crowds attenion when going for a easy drive.

But back to the subject.Either of them are pretty quiet.Yeah R31 nismoid id like it to be able to handle track days,which i am sure it will,thats all.

  • 1 month later...

i have a hks pod on my 33 and the standard plumbback valve going off sounds just as loud as my mates blitz atmospheric venting bov, i also get this cool sucking whistle when i floor it

i would recommend the stealth fx

but they dont come in black for the r33 at least they didnt when i bought one ... mines brushed silver looks nice too ... you can take the trumpet off and turn it to plumb back cops wouldnt say a thing about it ...

as for the pod i've got one of those too (they sound tough) in a box from linton of garage debris ... if i turn the stealth fx to full plumb back i still get a chopping noise on light throttle

the stealth fx can also be heard operating at full plumb back ...

if you dont want the psssshhhh sound and your not running 30 psi why bother changing it from standard ...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • perhaps i should have mentioned, I plugged the unit in before i handed over to the electronics repair shop to see what damaged had been caused and the unit worked (ac controls, rear demister etc) bar the lights behind the lcd. i would assume that the diode was only to control lighting and didnt harm anything else i got the unit back from the electronics repair shop and all is well (to a point). The lights are back on and ac controls are working. im still paranoid as i beleive the repairer just put in any zener diode he could find and admitted asking chatgpt if its compatible   i do however have another issue... sometimes when i turn the ignition on, the climate control unit now goes through a diagnostics procedure which normally occurs when you disconnect and reconnect but this may be due to the below   to top everything off, and feel free to shoot me as im just about to do it myself anyway, while i was checking the newly repaired board by plugging in the climate control unit bare without the housing, i believe i may have shorted it on the headunit surround. Climate control unit still works but now the keyless entry doesnt work along with the dome light not turning on when you open the door. to add to this tricky situation, when you start the car and remove the key ( i have a turbo timer so car remains on) the keyless entry works. the dome light also works when you switch to the on position. fuses were checked and all ok ive deduced that the short somehow has messed with the smart entry control module as that is what controls the keyless entry and dome light on door opening   you guys wouldnt happen to have any experience with that topic lmao... im only laughing as its all i can do right now my self diagnosed adhd always gets me in a situation as i have no patience and want to get everything done in shortest amount of time as possible often ignoring crucial steps such as disconnecting battery when stuffing around with electronics or even placing a simple rag over the metallic headunit surround when placing a live pcb board on top of it   FML
    • Bit of a pity we don't have good images of the back/front of the PCB ~ that said, I found a YT vid of a teardown to replace dicky clock switches, and got enough of a glimpse to realize this PCB is the front-end to a connected to what I'll call PCBA, and as such this is all digital on this PCB..ergo, battery voltage probably doesn't make an appearance here ; that is, I'd expect them to do something on PCBA wrt power conditioning for the adjustment/display/switch PCB.... ....given what's transpired..ie; some permutation of 12vdc on a 5vdc with or without correct polarity...would explain why the zener said "no" and exploded. The transistor Q5 (M33) is likely to be a digital switching transistor...that is, package has builtin bias resistors to ensure it saturates as soon as base threshold voltage is reached (minimal rise/fall time)....and wrt the question 'what else could've fried?' ....well, I know there's an MCU on this board (display, I/O at a guess), and you hope they isolated it from this scenario...I got my crayons out, it looks a bit like this...   ...not a lot to see, or rather, everything you'd like to see disappears down a via to the other side...base drive for the transistor comes from somewhere else, what this transistor is switching is somewhere else...but the zener circuit is exclusive to all this ~ it's providing a set voltage (current limited by the 1K3 resistor R19)...and disappears somewhere else down the via I marked V out ; if the errant voltage 'jumped' the diode in the millisecond before it exploded, whatever that V out via feeds may have seen a spike... ....I'll just imagine that Q5 was switched off at the time, thus no damage should've been done....but whatever that zener feeds has to be checked... HTH
    • I think Fitmit had some, have a look on there (theyre Australian as well)
    • Hah, fair enough! But if you learn with this one you can drive any other OEM manual. No modern luxury features like auto rev-matching or hillstart assist to give you a false sense of confidence. And a heavy car with not that much torque so it stalls easily. 
×
×
  • Create New...