Jump to content
SAU Community

Recommended Posts

Befor anyone gets upset i have serched and spent many hours on the net looking and got no where.

Im after a plastic frount bumper an after market one,

I have a R33 gts-t and have the origanl M-spec one on at the moment and wish to have a plastic one due to where i live and how much abuse the origanl one can take.

So the question is where and how much to get a after market plastic frount bar in any style 400R/ trial/ do-luck any, just want to know where to get it and how much?

Link to comment
https://www.sau.com.au/forums/topic/75958-plastic-body-kits-where-and-how-much/
Share on other sites

  • 2 weeks later...

amen to plastic bars! What could you pick up an OEM gtr bar for? I'm sure there's someone here that can tell us for sure whether it would fit or not... there might be enough give to get away with it. how about OEM 400r bar :bananaman :hearts: :headbang: We can but dream :D

There are a few japanese body kit makers that manufacture kits in ABS plastic and are as forgiviing as the original plastic bumpers.

To locate them go out and buy the latest option magazine, or hyper rev magazine and u should be able to locate them.

Cost is usually in the region of 1.8k i tink (excluding freight and taxes)

not sure who makes it but i saw a add in either ralph. autosalon or something similar a while back, about plastic bars, that can bend and contort, and not get damaged, they had a bar being fully twisted and it went back into place perfectly, i think they were expensive though, around 3k if i remember.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah well per the video it took 15s for the stock unit to start up....even if I give it a few seconds discount for starting that is at least 12 sec before you get a reverse camera if you are trying to leave a park.  The android unit is way faster, but 2016 for the stock unit is a long time ago in consumer electronics
    • Yea that’s why I said ima test them with multimeter and see the reads.
    • Only at idle. Isn’t a problem when rev it seems.
    • @Haggerty This seems silly to ask, but are you confident in your ability to tune the Haltech?  
    • Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
×
×
  • Create New...