Jump to content
SAU Community

does any one have a plastic aftermarket frount bar

Let Me Drive

By Let Me Drive,
in Victoria

 Share

Recommended Posts

Let Me Drive Mentor

Let Me Drive

Posted
Posted

Befor anyone gets upset i have serched and spent many hours on the net looking and got no where.

Im after a plastic frount bumper an after market one,

I have a R33 gts-t and have the origanl M-spec one on at the moment and wish to have a plastic one due to where i live and how much abuse the origanl one can take.

So the question is where and how much to get a after market plastic frount bar in any style 400R/ trial/ do-luck any, just want to know where to get it and how much?

so if anyone has one or knows where to get one info would be great.

i have rung jetspeed and other companys but no good.

inark Grand Master

inark

Posted
Posted

OMG U TOOL USE THE SEARCH!!! FFS OMG OMFG GG!!! lol jk

u really want a plastic one? i dont think anyone makes em anymore... most japanese brand bars are FRP - Fibreglass Reinforced Plastic

Its just as good... u can twist sideskirts around and they dont brake

If you want something like that u better have some good cash saved up.

CNR33 Community Regular

CNR33

Posted
Posted
no wait... its not FRp... whats the other one they use that twists??

plastic? :wassup:

Sorry Scott, I was in the same boat, did a bit of hunting when i was looking for a new front bar, no luck, pretty much everything is fibreglass

inark Grand Master

inark

Posted
Posted

nope... not everything... like i said... if u want the flexible stuff then u have to PAY a lot... ie. URAS FRP bars are on average 28,000yen... Their V system which twists without cracking is 50,000+yen...

btw - the search thing was a joke...

Let Me Drive Mentor

Let Me Drive

Posted
  • Author
Posted

so yes im not to shore about the exchange rate what would that be for either one in aus dollers cos i dont want the painfull job of always haveing to get the bar repainted every time i drive home on the dirt roads even going 10km still gets chiped.

thanks inark for this

inark Grand Master

inark

Posted
Posted

generally you cant mod the original bar very easily as it sits out a fair bit more than the GTST gaurds (this is on a 32)... to fit it properly you need to fit the gaurds and indicators from a GTR like i had on mine.

you can however buy aftermarket ones made for GTSTs... however im not sure theyre made of plastic.

I would say to fit a genuine GTR bar to an R33 it would be a similar setup... gaurds, indicators and maybe even the bonnet.

inark Grand Master

inark

Posted
Posted
yeah but was something different and well aftermarket so does anyone know where to get one of these URAS FRP bars from ?

you dont wanna URAS one for a 33... they look shocking ;)

unless u want ur car lookin like a duck ;)

http://www.uras.co.jp/syohin/skyline.html#r33

there are other brands that also use similar materials... do-luck, vertex, BN Sports...

z_33skyline_front.jpg

EDIT: scratch that just checked the site and it looks like BN is also FRP which is still better than the cheap copies we get here... but not as flexible

Let Me Drive Mentor

Let Me Drive

Posted
  • Author
Posted

yep i agree so where and who do i speek to to get one of these frount bars cos im sick of talking to people like jetspeed who say "why dont you just get a fiber glass one" (i dont want a fiber glass one) so yeah

thanks inark if you have any one you know who can get one i would love to talk to them.

and $1000 is not out of the question cos it would last longer and look much better then a fiberglass one.

krzysiu Grand Master

krzysiu

Posted
Posted

Could i get a mould of my Bomex Front bar and get it remade in plastic? I think it would be better to pay a little more then keep on repairing it because of driveways. I just cracked mine on a gutter last night ;)

**JaR** Grand Master

**JaR**

Posted
Posted
so yes im not to shore about the exchange rate what would that be for either one in aus dollers cos i dont want the painfull job of always haveing to get the bar repainted every time i drive home on the dirt roads even going 10km still gets chiped.

dude i drive home on dirt roads for about 3kms a day, and my front bars fiberglass, and mine goes alright without huge chips and stuff, unless the roads you gotta drive down are REAL bad. plastic still gets chipped and stuff anyways, mate of mine had a plastic front bar on his lancer, still got chipped .. living in a place where there are dirt roads maybe you dont got a choice mate ;).

inark Grand Master

inark

Posted
Posted

plus plastic is black not white like most glass bars so when the paint does chip on a plastic bar it doesnt stand out like dogs balls... especially on a dar coloured car

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      Next on the to-do list was an oil and filter change. Nothing exciting to add here except the oil filter is in a really stupid place (facing the engine mount/subframe/steering rack). GReddy do a relocation kit which puts it towards the gearbox, I would have preferred towards the front but there's obviously a lot more stuff there. Something I'll have to look at for the next service perhaps. First time using Valvoline oil, although I can't see it being any different to most other brands Nice... The oil filter location... At least the subframe wont rust any time soon I picked up a genuine fuel filter, this is part of the fuel pump assembly inside the fuel tank. Access can be found underneath the rear seat, you'll see this triangular cover Remove the 3x plastic 10mm nuts and lift the cover up, pushing the rubber grommet through The yellow fuel line clips push out in opposite directions, remove these completely. The two moulded fuel lines can now pull upwards to disconnect, along with the wire electrical plug. There's 8x 8mm bolts that secure the black retaining ring. The fuel pump assembly is now ready to lift out. Be mindful of the fuel hose on the side, the hose clamp on mine was catching the hose preventing it from lifting up The fuel pump/filter has an upper and lower section held on by 4 pressure clips. These did take a little bit of force, it sounded like the plastic tabs were going to break but they didn't (don't worry!) The lower section helps mount the fuel pump, there's a circular rubber gasket/grommet/seal thing on the bottom where the sock is. Undo the hose clip on the short fuel hose on the side to disconnect it from the 3 way distribution pipe to be able to lift the upper half away. Don't forget to unplug the fuel pump too! There's a few rubber O rings that will need transferring to the new filter housing, I show these in the video at the bottom of this write up. Reassembly is the reverse Here's a photo of the new filter installed, you'll be able to see where the tabs are more clearing against the yellow OEM plastic Once the assembly is re-installed, I turned the engine over a few times to help build up fuel pressure. I did panic when the car stopped turning over but I could hear the fuel pump making a noise. It eventually started and has been fine since. Found my 'lucky' coin underneath the rear seat too The Youtube video can be seen here: https://www.youtube.com/watch?v=uLJ65pmQt44&t=6s
    • hoodedreeper
      Chris' Toyota Mark ii JZX110

      By hoodedreeper · Posted

      It was picked up on the MOT/Inspection that the offside front wheel bearing had excessive play along with the ball joint. It made sense to do both sides so I sourced a pair of spare IS200 hubs to do the swap. Unfortunately I don't have any photos of the strip down but here's a quick run down. On the back of the hub is a large circular dust cover, using a flat head screw driver and a mallet I prised it off. Underneath will reveal a 32mm hub nut (impact gun recommended). With the hub nut removed the ABS ring can be removed (I ended up using a magnetic pick up tool to help). Next up is to remove the stub axle, this was a little trickier due to limited tools. I tried a 3 leg puller but the gap between the hub and stub axle wasn't enough for the legs to get in and under. Next option was a lump hammer and someone pulling the stub axle at the same time. After a few heavy hits it released. The lower bearing race had seized itself onto the stub axle, which was fine because I was replacing them anyway. With the upper bearing race removed and the grease cleaned off they looked like this The left one looked pristine inside but gave us the most trouble. The right one had some surface rust but came apart in a single hit, figure that out?! I got a local garage to press the new wheel bearings in, reassemble was the opposite and didn't take long at all. Removing the hub itself was simple. Starting with removing the brake caliper, 2x 14mm bolts for the caliper slider and 2x 19mm? for the carrier > hub bolts. I used a cable tie to secure the caliper to the upper arm so it was out of the way, there's a 10mm bolt securing the ABS sensor on. With the brake disc removed from the hub next are the three castle nuts for the upper and lower ball joints and track rod end. Two of these had their own R clip and one split pin. A few hits with the hammer and they're released (I left the castle nuts on by a couple of turns), the track rod ends gave me the most grief and I may have nipped the boots (oops). Fitting is the reversal and is very quick and easy to do. The lower ball joints are held onto the hub by 2x 17mm bolts. The castle nut did increase in socket size to 22mm from memory (this may vary from supplier) The two front tyres weren't in great condition, so I had those replaced with some budget tyres for the time being. I'll be replacing the wheels and tyres in the future, this was to get me on the road without the worry of the police hassling me.
    • Haggerty
      RB25DE NEO with Haltech ECU

      By Haggerty · Posted

      Yep, the closest base tune available was for the GTT, I went with that and made all the logical changes I could find to convert it to Naturally Aspirated. It will rev fine in Neutral to redline but it will be cutting nearly 50% fuel the whole way.  If I let it tune the fuel map to start with that much less fuel it wont run right and has a hard time applying corrections.  These 50% cuts are with a fuel map already about half of what the GTT tune had.  I was having a whole lot of bogging when applying any throttle but seem to have fixed that for no load situations with very aggressive transient throttle settings. I made the corrections to my injectors with data I found for them online, FBCJC100 flowing 306cc.  I'll have to look to see if I can find the Cam section. I have the Bosch 4.9 from Haltech. My manifold pressure when watching it live is always in -5.9 psi/inHg
    • brillo
      Leak from Tokico BM50 Brake Master Cylinder

      By brillo · Posted

      Hi My Tokico BM50 Brake master cylinder has a leak from the hole between the two outlets (M10x1) for brake pipes, I have attached a photo. Can anyone tell me what that hole is and what has failed to allow brake fluid to escape from it, I have looked on line and asked questions on UK forums but can not find the answer, if anyone can enlighten me I would be most grateful.
    • MBS206
      Cas issue

      By MBS206 · Posted

      It will be a software setting. I don't believe many on here ever used AEM. And they're now a discontinued product,that's really hard to find any easy answers on. If it were Link or Haltech, someone would be able to just send you a ECU file though.
×
×
  • Create New...