Jump to content
SAU Community

Recommended Posts

$400 for 18s????  That can't be right anyways...should have done a search b4 asking the stupid question...:)  Thanks for all the input.  Got a set of Goodyear GSDIIIs quoted at around $1800 fitted.  Will try and get a few more quotes before deciding. Meantime, if anyone has any recommedations with pricing let me know.

Thanks!

I can get you toyo T1R's in 275x35x18 for $340 each but i dont know how much it will cost to freight to Bris .

Then again you can only use 2 for the rear so probably not worth the trouble .

scenario

zeix, FC rx7, lots of rear negative camber, just been through car wash.

ok i did a left hand turn at about 25kph, i wasnt accelerating at all, i was just coasting in second gear SLOWLY, like i could take this corner on the angle that i did it at 60 with dry tires and some acceleration. anyway the risidual water from the car wash made it slippery enough that the rear completley switched ends with the front, i managed to catch it but if anyone other than me was driving the car they woudlve been facing backwards into oncoming traffic.

i dont trust the zeix in the wet at all, driving up old beliar road in adelaide at 60 in the wet i was having to countersteer the entire way up due to the oversteer driving up the road at 60 in third gear was causing from wheelspin. its downright dangerous, i daresay that if my mum or dad had been driving the car at the time they wouldve been straight into the guardrail

much prefer the bridgestone grid 3's i had prior to these

I have them on my GTS-T and they are pretty bad. I've got a stock car (bar cat back), and one a cold night i'll have no traction in first, at all. I've got 235 * 17s. In the wet, if I touch boost in the first three gears, she'll start spinning. I feel these tyres are way too hard of a compound.

I'd love to go drag race my car, but I don't think I will on these tyres... i'd run a > 15 second pass due to the wheel spin, haha.

Let me know what you end up going... I've been thinking about changing the rears to Yokohamas.

I just got a set of 235/18s 326s and they hook up ok in the dry. So i take they go to sh1t once you put a few kms on them?

Anyway, i think they were $170 each, though the 265s may be a bit more expensive. I ho[pe they are a good durabel tyre, based on what i have read here just have to be sure to take it extr careful in the wet...but they cant be anyworse then the D01Js in the wet can they??? Anyway 326s for the street as they were cheap and hopefully good wear, RE55s for when i want traction:)

Thansk for the headsup re 326s:thumbsup:

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Lamb roast on Saturday will be different 🥲
    • They are under bucket shims. Tomei provides a test shim kit and then any measurement of shim required. 
    • I always wondered how you were supposed to buy a set of 24 buckets and somehow magically have every single one of them yield exactly the desired clearance. I would have thought you'd need to assemble a cam with either 12 "sample" or "example" buckets of known top thickness (or a single such sample/example 12 times over!!) measure clearances at every valve, and then do the usual math to work out what the actual "shimness" of each bucket needed to be, before buying the required buckets to make up he thicknesses that you didn't have on hand.
    • I now seem to be limited in power due to my rev limit/hydraulic lifters in my built RB25. I'm looking into converting over to Tomei solid lifters. Question for anyone that has done the conversion. I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  I don't know where I got this idea, as so far I see no mention of this in any of the Tomei documentation. It just states I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
    • I couldn't agree more. I should have started from the get-go with a NEO or solid bucket conversion. I started looking into converting over to solid lifters yesterday. Now for some reason I was always under the impression that when using the Tomei solid lifter conversion, you would also require new valves (Longer or shorter stems, I can't remember which).  But I see no mention of this on any of the Tomei documentation. It just states that I need the Tomei solid buckets, solid lifter cams and upgraded springs. As my head is already built, all I would need is another set of 1000$ Kelford cams, 500$ buckets and about 4H hours of my time installing and I'm off to the races!?!? There's no way it's that simple, I must be missing something? 
×
×
  • Create New...