Jump to content
SAU Community

Recommended Posts

I will post here cos u can't attach pics to a PM.

You can have it for $40 if you want it - I think it cost me about $60 to get made up.

Pics attached - the flange bolt holes are at a 45 degree angle to each other .... not sure if this is normal, but you would want to check. I hope the pics show what I mean.

I am in Northgate fyi

Sorry, it looks like the sale is goin to Nightcrawler. But, yeah the flanges are meant to be set at 45degrees of each other on the cat. It should be a direct fit to your standard or aftermarket exhaust, provided its not a custom one. In the unlikely event it doesn't fit it only cost around $15 for Profix to knock out & re-weld flanges to align with exhaust.

ok...it seems the flanges on my cat apperar to be the same as your replacement pipe nightcrawler. Can u pm me your number so i can pick it up?

I need it tonight as my car goes into shauns tomorrow morning for a tune :cheers:

My cat is roughly 320mm long too...is that about the same as your pipe?

Northgate aint that far from me either...in near tea tree gully.

the pipe is excatly 342mm long from tip to tip - I am sure that is close enough!

I just tried to ring your mobile, but there was no answer. I'll PM u my phone number now.

well, had the new pipe fitted, and exhaust put on. All sounded sweet.

Then had the car put on the dyno where shaun started to give the car a tune to see what she could get.....

Made absolutley SFA difference....the car makes about 133 odd rwkw last time i had it tuned before it started to struggle to make power.Now the top end is better, and it makes a little more power but she struggles like hell.

It topped out at roughly 145odd rkwk then didnt make any more. :) Needs to go back to Shauns in a week or two for some problem solving. Might be cam timing is off, or something stupid like a boost leak.....who knows :(

Im soooo pissed....but the car does sound very nice with its "free flowing cat" now :cheers:

is this power figures for your RB31DET? i'm presuming your engine is fully standard aswell as your turbo? how different is yours to joel's?

Yes its my rb31det.

My engine is built to the exact same specs as Joels. (they were built side by side :) )

Turbo is a rb20det highflow jobbie (not done by me, but previous owner of the car).

My engine only has a few bits like rb20det oil pump (joel used rb25det) bigger fuel system (550cc, 044) and q45 afm/pod. Other than that they are identical.

I had some STR cam gears fitted when i had the motor installed, and Shaun reckons they may be a tooth out. :( I dunno myself, but it has to go back to get it all sorted in a week or two.

Dont worry about it Maxx, we were justy finishing as Joel went to leave....it wasnt gunna make any more power yesterday unfortunatly :(

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • What an awesome idea to fit the facelift Lamborghini Diablo headlights. They are a perfect fit!
    • An update regarding the registration with the DVLA I sent off the paperwork the day after I collected the car from the port, two weeks later it was all returned with a letter explaining they have rejected the application. This was because the cheque was £20 short for the road tax (I used a price list I found online). Nevermind it is what it is, it was sent back to them the following day with a new cheque. Fast forward another 2 weeks or so, I called them for an update to be told it had been rejected. Yesterday (16th September) I received the documents back along with another letter, this time it was because I didn't put an X in one box on the V750 (personalised number plate certificate), which declared that I had the rights to the personalised number plate. Why this wasn't mentioned in the first rejection letter, I don't know, but it could have saved this headache. The documents were sent back today, so fingers crossed third times a charm and it'll FINALLY be registered on the road just in time for the bad weather (woohoo!) To cheer myself up I lowered the front 25mm, was sick of seeing it sit like a monster truck. No idea how much clearance I'll have getting on and off the driveway, I'll worry about that when I can actually drive it
    • You're going to miss not worrying about rust in the strut towers like the Skyline shitboxes out there
    • A few little updates that weren't filmed due to not taking long to do or not interesting enough for their own video. My new K&N Air Filter arrived, I went with an RU-4180 which matched the dimensions of the universal cone filter the car originally had.  The battery had gone flat, while that was charging I tidied up the spaghetti wiring at the bulk head and down the sides of the engine Next job was to swap the stereo The Kenwood harness had the female ISO plugs cut off and the male ISO plugs cut off the adaptor loom and joined with bullet connectors. I ordered in a repair loom through work and re-did it all. New Kenwood unit installed (Android Auto, DAB, Bluetooth, Reverse Camera) The bonnet/hood gas struts have been poor since collecting the car. I couldn't find any suitable replacements locally so took a chance on a pair from AliExpress.  The originals don't use a retaining clip to secure the cup onto the ball fixture, would explain why I struggled for 10-15mins trying to pry off the cups. The ball fixtures unscrew using a 12mm spanner, new ones are the same size. Sadly no photo of them fitted, you're not missing much lol The dished Momo steering wheel got replaced with my Momo Tuner, turns out I ordered counter sunk bolts for the horn trim ring (like they normally are for the steering wheel) instead of allen cap (flat seat)  A terrible photo of a Quaife style gear shift knob I've had stashed in my tool box for many years after purchasing the incorrect thread size (I can see a pattern emerging with ordering incorrect parts...) Also threw in a cup holder and a (empty) Boss Coffee can, because why not  
    • GT-R clearly the better choice! The 300 is certainly not insaly fast but has a decent amount of poke. Does a nice little drift around the corners with a decent amount of throttle. It's VERY predictable in a slide too.  Feels so progressive! People probably presume there's a 25 year old driving it based on my behaviour this week! 🤣
×
×
  • Create New...