Jump to content
SAU Community

Recommended Posts

  • Replies 162
  • Created
  • Last Reply

Top Posters In This Topic

I manage a metallurgy laboratory.

If someone can arrange for sample of the substrate (a gram is plenty), I'll have an analysis back within 24 hours as to whether it contains any platinum group metals (Pt, Pd, etc) or indeed anything other than what's in a normal s/steel alloy.

Cheers

Gav

I manage a metallurgy laboratory.  

If someone can arrange for sample of the substrate (a gram is plenty), I'll have an analysis back within 24 hours as to whether  it contains any platinum group metals (Pt, Pd, etc) or indeed anything other than what's in a normal s/steel alloy.

Cheers

Gav

What's postage like from Australia to Bulgaria? :)

BOOSTD,

the 'metal cats' are good cats. we've tested those and they came up with good results on emissions, just like they clearly state.

the difference between the metal cat and this new catco cat is the body. the metal cat is quite small, i think its the same body size as the magic cat (4"), whereas the catco one is larger (5") and can pass through more exhaust gas than those. both have 200 cell pr sq inch catalysts, whereas magic cat has 300 cell per sq inch. this just means that the metal cat and catco cat have larger holes, thus being able to let through more exhuast gas than the magic cat.

either way though, the metal cat doesnt need cone reducers, as it already has them, like the catco cat, with 3" piping at the ends. the magic cat however needs all those extra bits (cone reducers, 3" piping) welded on, as its just a 4" pipe, this adds up, and because its not done by a machine, it would probably be quite rough in the end, depending on the skills of the person doing it for you at the exhaust shop...

keep a look out in the next issues in different magazines (e.g fast fours, HPI etc), you will notice hi-tech mufflers, liverpool exhaust and a few other well known exhaust shops advertise the new catco cats. i know hi-tech have been doing some dyno tests on the WRX with some very interesting dyno results.

HAHAHAHAHAHH this is funny!

How many people have bought cats that are just a fancy straight through pipe?

You got ripped off guys :P

Must... not... feed... the... troll.....

You have evidence its just a straight through pipe? Post it up. Or is this just going to be like your tirade against import agents?

Guest
This topic is now closed to further replies.



  • Similar Content

  • Latest Posts

    • our good friends at nismo make a diff for it, I have one (and a spare housing to put the centre in) on the way. https://www.nismo.co.jp/products/web_catalogue/lsd/mechanical_lsd_v37.html AMS also make a helical one, but I prefer mechanical for track use in 2wd (I do run a quaife in the front, but not rear of the R32)
    • What are we supposed to be seeing in the photo of the steering angle sensor? The outer housing doesn't turn, right? All the action is on the inside. The real test here is whether or not your car has had the steering put back together by a butcher. When the steering is centred (and we're not caring about the wheel too much here, we're talking about the front wheels, parallel, facing front) then you should have an absolutely even number of turns from centre to left lock and centre to right lock. If there is any difference at all then perhaps the thing has been put back together wrongly, either the steering wheel put on one spline (or more!) off, and the alignment bodged to straighteb the wheel, or the opposite where something silly was done underneath and the wheel put back on crooked to compensate. Nut there isn't actually much evidence that you have such a problem anyway. It is something you can easily measure and test for to find out though. My money is still on the HICAS CU not driving the PS solenoid with the proper PWM signal required to lighten the load at lower speed. If it were me, I would be putting either a multimeter or oscilloscope onto the solenoid terminals and taking it for a drive, looking for the voltage to change. The PWM signal is 0v, 12V, 0V, 12v with ...obviously...modulated pulse width. You should see that as an average voltage somewhere between 0V and 12V, and it should vary with speed. An handheld oscilloscope would be the better tool for this, because they are definitely good enough but there's no telling if any cheap shit multimeter that people have lying around are good enough. You can also directly interfere with the solenoid. If you wire up a little voltage divider with variable resistor on it, and hook the PS solenoid direct to 12V through that, you can manually adjust the voltage to the solenoid and you should be able to make it go ligheter and heavier. If you cannot, then the problem is either the solenoid itself dead, or your description of the steering being "tight" (which I have just been assuming you mean "heavy") could be that you have a mechanical problem in the steering and there is heaps of resistance to movement.
    • Little update  I have shimmed the solenoid on the rack today following Keep it Reets video on YouTube. However my steering is still tight. I have this showing on Nisscan, my steering angle sensor was the closest to 0 degrees (I could get it to 0 degrees by small little tweaks, but the angle was way off centre? I can't figure this out for the life of me. I get no faults through Nisscan. 
    • The BES920 is like the Toyota Camrys of coffee machines. E61 group head is cool, however the time requirements for home use makes it less desirable. The Toyota Camry coffee machine runs twin boilers and also PID temp control, some say it produces coffees as good as an E61 group head machine.
    • And yes with a full tank it will hit limiter free revving or driving 6B6CDF6E-4094-426D-A9CB-6C553475FE36.mp4
×
×
  • Create New...