Jump to content
SAU Community

Recommended Posts

Just want to get some feedback on the stock ECU. I am boost cutting at under 10psi....I think (not sure if boost cut or other..i.e coils)

The coils have burn marks down the side but I can see no arcing at idle or when reving the motor (I have taken the cover off the top)

Thinking now it must be boost cut.

1. What boost level do you cut out at?

My car has R34 intercooler and 3" exhaust..that's it. Tried a few different boost control methods. Both cause an engine cut. Warm or cold.

and

2. The AFM gives out a reading from 0-5 volts I believe. What voltage does the ECU determine that airflow is to high? I guess it may depend on inlet temp etc aswell?

I was boost cutting or equivalent at 3000rpm in 4th gear so it wasn't as if the inlet temp was high. Just put the foot down up a hill.. after going easy at 80km/h

hi ben,

ecr33 series 2, hits the stock boost cut around 11psi ish. feels like you hit an invisible wall (much like 180 speed cut). all the usual noises happens, boost shows 11psi on the guage and stocker gauage but you get jack all power from it. that was ecr33, pod, zorst, evc3 @ 0.80bar. then i got cooler and powerfc. afm goes from 0 to 5.10 volts. the stock ecr33 ecu doesnt know what air inlet temp is, it has no support for it. only amount of air coming in via airflow meter. do you get any popping/farting when you get this problem? the ecu dumps the timing and richens it up mega so you should get popping and farting in theory ?

Thanks Paul!

It is like you say an invisible wall but didn't appear to pop and fart. I guess at 9.5psi I'm not far away from 11psi so maybe in fact mine is the overboost or over airflow cut.

So the AFM has to register near 5.1v to boost cut??

At the higher boost it tends to feel like it is missing sligtly as you rev it to redline (only sometimes though). Only just lately is started cutting. Running stock boost now and it is fine..although some people have had coil probs that only show up when boost increases...

what mods do you have ben? im not sure what voltage the stock ecu considers "too much" and goes into rich and retard (aka boost cut) but its probably somewhere near 4v or higher. if you run slightly lower boost do you effectively work around the problem?

What you are experiencing isn't any sort of cut at all. A cut is a cut.. nothing, not an invisible wall.

You are experiencing the usual R33 ECU rich and dip safety 'feature'.

The R32 ecu on the other hand doesn't have the rich and dip safety feature. Instead it allows you to keep pushing it until BANG.. no ignition you literally loose all power, it feels like you have slammed on the brakes and the rear wheels compression lock. Its not fun and makes you seriously thing you have broke something. :D

The R32 ecu experiences this with the RB20DET at around 5500rpm @ 17psi with the stock turbo.

i have come across similar sort of promblem but i was running 11.9 and 11 psi boost.

At 11.9psi there was huge power dip and at 11psi it was less but it was noticeable.

When i ran my stanadard actuator at 7psi i good power curve with correct air fuel ratios.

i have dyno all the above pressures and yet havent found a suitable pressure above 7 psi.

I am trying to find out what is cause of this power dip?

Is it that the air flow meter can no read the flow of air or the ecu can not read the air flow signal given by the air flow meter?

Or it is at a specific pressure the ecu goes on to limp mode?

Are there any other factors that decide it ?

Can Safc work?

stock boost cut ???

ive got a r33, normal basic mods.. does that mean when it has 12psi for e.g on the boost gauge its only running at 11 ????

Im using the stock ecu with safc2, dont tell me theres some stock boost cut and i should of got the powerfc pls???

thanks :cheers:

(uve got me worried now)

Do search ppls, its been covered many many times.

Its very very common for the stock r33 ecu to generate power dips through the power range. 'Generally' this occurs over 10-11psi'.

But really whats 1psi.. It could be your boost guage thats out.

Im using the stock ecu with safc2, dont tell me theres some stock boost cut and i should of got the powerfc pls???

yeah thats basically it, after a certain amount of airflow the ecu goes into protect itself mode. its not that bad, once you run around that boost level its not useful going any higher with the stock turbo as it wont make any more power.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Nah, new members can't post pics until they reach a certain post count. If I get a chance I'll promote you to full member, if @Prank or someone else doesn't get there first.
    • Drilled the rubber out on a slow speed and it didn't catch much at all. Probably only half a dozen holes was enough to shred the rubber and it dropped off easily leaving the inner sleeve behind. Will tackle that later
    • I havent bought a manual cover for the dash yet and no cluster change, won't bother me too much, I just need to get that auto box gone, manual in! I miss my manual. 🤪. We started last weekend and managed to get the box out. Planning to start putting it in this weekend and then order a single piece tail. We were super careful to take time and not damage anything. It's my first time working under the car.  With my S15 mainly worked in the bay. This time, it was a headache because of three or four bolts only. They simply didnt want to leave thei homr and the one securing the tailshaft, another above the GB, and the one securing the lipstick was a shit. Mates mate, Davo caught fire 🤣, nearly opened his chest up with a grinder 🤦🏽‍♂️ and both mates nearly had a plate from the box land and slit their head open. Fun times. We all survived. Not the easiest working with limited access on jackstands. As I'm sure we can agree these are the memories which make us love our car. For all three of us, was an awesome weekend and Sunday 3.30am before tools down was a fantastic effort. I need to upload pics, but looks like it needs to be via Url now. We used to be able to just upload pics back in the day. It's been that long! 🤪 Im currently spraying rustoleum under body, not because it's rusted. It's super clean, but just so it's protected for the next 10 years. There was a few surface rust spots. Which pretty much wiped off with a 3M scourer.  Really impressed with how well the previous owner maintained it. Bank account went down so quick! Service, then GB - managed to get a spanking new 34 genuine box from Nissan. All the rest of the conversion parts from Kudos.  Went with a Nismo short shifter. New pedals and Exedy Clutch and FW. Ordered the Prp Rear Main Retainer kit which should arrive Friday and my first engine mod part just like I did with my S15 will be the Tomei Expreme Turbo Outlet. Already on order. It'll likely sleep next to me on a pillow during the coming months. 🥰 Last build was on my JET200GT profile and on SAU and Hardtuned I had documented the build. Planning to try to do that again. Brands feel scarce now. Wish we still had ARC and Apexi parts readily available. Exhaust - need some advice on this. I had an Apexi exhaust on the S15 and loved the tone. My mate had a HKS HP Silent on his 33 and suggested I go with that to avoid drone. I can't remember hearing an RB25DET running that so will likely need to wait for a meet or something to hear it.  Not after big power, just enjoy building it, and drivability with minimal negative attention.
    • Have a chat with Ben at Moore Performance or Jesse at JS Performance.
    • Thanks both. All good advice. Reminds me of drilling through stone wall for drainage pipe 😬 I'll let you know how I get on if I still have use of my hands afterwards 😅
×
×
  • Create New...