Jump to content
SAU Community

Recommended Posts

Hi,

Ive got a manual 34 with turbo back 3" exhaust, apexi pod, hks bov, avcr (0.7 bar) and power fc. The mods were fitted in this order first exhaust > pod > avcr > pfc.

After I had the Power FC tuned I was slightly dissapointed with the 'increase' in power (it was tuned on the road, not a dyno by chapman & chapman). Since then I haven't been too worried about it as the car is running perfectly, and the tuner had ironed out a 'miss' I had on idle and some backfiring between gears caused by the atmo bov. It was only today that I realised my car is hardly any quicker than a standard manual sedan (judging purely by 'feel').

Just now i swapped back to my standard computer and it doesn't really feel hardly any slower..... I am going to run it on a dyno -

My question is how much power (at least) should I expect?

Dan666 was also in my car and agreed it should be a lot quicker......

Any ideas??

Cheers, Paul

Link to comment
https://www.sau.com.au/forums/topic/76608-r34-performance-issues-with-pfc/
Share on other sites

Hmmm - cheers bass i'll see how I go.

By the way I ran 13.9 @ 101mph with 2.21 60 foot - That was a 3500 launch (obviosuly not dropping the clutch) and it was on 19" chromes with 235's. Also remember its a sedan... Bass - how did you get a 1.9 60 foot?

I was quite happy with this time - although shoudl i expect more? I think the sedan is at least 150kg heavier than the coupe?

Your missing a fmic.......

I went through the same thing in my car......I got the PFC by necessity as my afm stuffed up and I decided to get a z32 and pfc while I was at it.

I had pretty much the same mods, exhaust, pod, blitz ID3, z32 and pfc.

Have to admit the pfc DID make a little bit of difference but not as much as I expected, but once the front mount was installed and the pfc had a bit more room to do its magic it made a HUGE difference.

Admittedly the dyno is a bit of a happy dyno...but the difference the fmic should be legit as it was done on the same dyno...

I ended up going from 183rwkw before fmic to 220rwkw after fmic.

  • 2 weeks later...

I got a front mount installed a few days ago. The car is alot quicker all the way through the revs. I can't belive it actually seems to have less boost lag - theres alot more response all the way through the revs. It actually felt 'doughy' before, now it feels almost like 2 people have got out of the car. It hasn't been retuned yet, i'm not sure how much would have to be adjusted with just the addition of an intercooler... it will be done this week some time.

I've driven a fair few cars (mainly 32's and 33's) with bigger front mounts and the same mods as mine minus the computer and really have felt hardly quicker than cars with stock coolers... maybe r34's with better breathing on the intake and exhaust and tighter a/f ratios really put alot more pressure on the stock cooler??

Either way i'm happy :P I'll get a dyno readout in a while and let you know - i'd be happy with anything over 190kw...

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • When you crank your car, and hit it with a timing light, can you see a steady crank timing?
    • Oh, forgot to add, A few months ago I was getting mixture codes and the car was using crap loads of fuel. You could smell the unburned fuel in the exhaust, it was crazy strong. Economy was over 17.5 l/100 and usually around 19. I smoked the engine and found a leaky CCV hose which I replaced and then I replaced my two pre cat O2 sensors, I also replaced the MAF. This fixed my mixture codes and improved my exonomy but I'm still 14 - 15 l/100 when pottering about town so something is still amiss. Throttle response is much better and it has more pep but I'd like to know why it's still so thirsty (and I'm hoping that whatever it is gives me a bit more poke).    
    • Car is on factory injectors/z32 maf/ q45 throttle body/ z32 ecu with nistune 
    • Hello all, currently finishing up a rb25 swap into my s14. Having issues with starting, car has spark (confirmed by pulling a plug and watching it spark), has fuel(confirmed by checking pulse/voltage at injectors all spark plugs are soaked in fuel). Car cranks over and pops into the exhaust with a heavy fuel smell but no attempt to start or run, I have torn the timing cover off and triple confirmed timing, turned the CAS in multiple spots both directions, attempted to start with coolant temp and maf unplugged, checked my fuel lines and made sure they weren’t backwards, checked voltage at cas/injectors/coilpacks, made sure all the grounds in the harness are connected and added a few grounding straps (1 from chassis to block, 1 from chassis to head, and 1 from chassis to igniter chip) I am getting stumped here. As a last ditch effort I made a full grounding harness tonight that’s going to run from the battery and add an extra ground from the battery onto the coil pack harness/igniter chip/ intake manifold/ Wiring specialties harness ground/ and alternator. I’m hoping maybe the grounding harness will fix it here but posting here to see if anyone has any other ideas on what else I can check. My fuel pressure is unknown right gauge will be here tomorrow.  IMG_3206.mov
    • yeah I was shocked when I checked my spare OEM on and as below that's how they come from Nissan. (side interesting note new NEO gearbox and replacement park lack the brass bush on the tips and its just all alloy) unsure about damage to the box currently back at 1110 to be pulled down/inspected and selector fork replaced as he built it previously and given the never before seen failure on his billet forks he is replacing it under warranty. He said he has used always OEM the keyway tab without issue for years so it could be an unlucky coincidence. I did talk to him about the sharp corners and stress concentration too. Re: hard shifts i got 7+ years out of the OEM one and the fork itself failed not the keyway. so could be bad luck as I said or an age thing + heat cycles in box and during fabrication of billet?
×
×
  • Create New...