Jump to content
SAU Community

Recommended Posts

OK guys just need some un-biased opinions. I've come to the conclusion that I need some type of fuel management aids. By looking at the dyno sheet, you can see some real bad dips (40hp near the end). I've been told that its the ecu and its retarding when running higher boost. (correct me if im wrong, this is just what ive been told by a few people as a 'possible cause')

dynosm.jpg

I want to know basically if I should bite the bullet and just go for a power FC, or do the cheaper Super AFC II option. Also.. I can get the Power FC off these forums for about $980 delivered, but how much is this going to cost to get fitted and tuned? The SAFC II is about $400 delivered, but is this cheaper to install and tune as well?

BTW mods are

seperated dump pipe to 3" s/s exh, hks pod, man boost control, Hybrid FMIC.

Link to comment
https://www.sau.com.au/forums/topic/77715-powerfc-or-safc-ii/
Share on other sites

the boost control itself seems to be a bit dip-py aswell, floating around 10psi..

ive got 3" split dump, 3.5" exhaust, pod filter, ARC 450 FMIC, Microtech LT-12 running a pretty stock config, except its a bit flat at the start of the rev range, and i get 270RWHP

(i dont have a picture of my dyno graphy handy, but its pretty much the same as yours, except at the start it gets more power pretty quick, then midrange it flattens off, then it jumps heaps towards the end, and begins to curve down a tad near redline, peaking at 270RWHP at about 135km/h, altho it was dyno'd in 3rd gear)

so it should be safe to say you could get another ~30hp, and a more steady graph with some decent management. :(

If you want to add hp by just changing the ecu & want to modify your car later on, PowerFC. The safc will give you the right air-fuel ratio though, it's just a question of budget. What boost are you running????

If that power dip is due to retardation a SAFC won't help because it only adjusts the fuel not timing I believe.

What did Lumpy recommend as he knows his Nissans so I would go with that.

Other than that I'm another vote for the PFC.

It plugs straight in and only has to be tuned as opposed to wired up then tuned so install and tune costs may not differ that much.

Cheers for the advice guys.

bnr#@ - Had the bumper off to re-fibreglass and paint, its back on now, driving around with a big fmic in front wouldnt be too smart :D

ossie_21 - Im running about 0.8ish of a bar. The car drives smoother when running lower boost tho, not so up and down. When running about .8, it takes off good, then tapers off then takes off again a bit. Feels very slow ;)

I think I may need to just bite the bullet and buy the power FC, its just $1600ish I can't really afford to spend at this time, but yeh chances are down the track I 'may' change the turbo, so power fc will seem like a better option

Just to throw a curve ball, sorry - but have you considered the Greddy e-manage?

It starts life as a SAFC, but can be cheaply upgrade to provide FULL management. Lap top programming etc. It really is a versatile ecu, cost a little more than the SAFC, but alot cheaper than power fc, especially initial purchase.

From someone that has done the SAFCII route and then gone the PFC, I would highly recommend going straight to the PFC. I certainly wish I had. If this means driving your car more sedately and saving the extra money, do it. I was very similar to you, had funds for SAFCII but not for PFC but in my opinion, the money i spent on SAFCII + tuning was essentially wasted cause the PFC is such a better tuning option.

Also, in relation to the dips, do a basic diagnostics. I had a serious dip in one of my curves at high rpm (and when i say serious, i mean 100rwhp serious) and this turned out to be a knock sensor wire come loose which a simple diagnostics detected. Plugged it back in, took it for a tune again and no dip. It may help, it may not, but hope it does :)

Yeh .. the group buy needs like 30 people tho. HASHIRIYA on these forums is selling power fc + commander for $1020 delivered to door, then put on however much to tune it. Yeh ive read that its a DIY job for sure.

Uneekwahn - $1600 was a rough supplied fitted and tuned price (with 1yr aust warranty)

Just wondering if its worth it buying myself, fitting it, then just driving it somewhere to tune, ive been told powerfc std settings is 'safe' but dont floor it until a tune. Anyone know how much it is just to do a first tune of a powerfc? Keep in mind i won the raffle @ hyperdrive on the weekend so i got a power run and dyno tune to value of $150 ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Another vote for installing them and see how you go.  I mean, you already own them, why would you not fit them? 
    • I have had too many of those over the years, my cars have a toolkit or at minimum a cheapy multi tool thing because its too easy to be snookered by some stupid plastic clip that stops you checking the battery terminal isn't loose.
    • Basically, if there is a part# on the nissan catalogue, it is a genuine part. There is a thing called "new old stock" which is stuff made years ago but never sold (or landfilled), but it is super hit and miss what you can buy. Other than some expensive Nismo stuff there is nothing new being made that suits these cars. The only time to be a little careful is (mostly in the US I think, but maybe Japan too), Nissan started rebranding some cheap crap maintenance parts like oil filters as "Pitworks"; stay away from them, if you are buying cheap just buy whatever the local car parts shop carries The three part numbers have an explanation on Amayama: 0V005 is auto, base style 0V015 is manual 0V505 is auto, hectic momo branded ones, maximum F&F points there!
    • You can trust Rezz!
    • Just to get this straight if you turn the splined shaft to the outside, it turns freely but the chain does not move? What happens when you move the chain, does the splined shaft turn? Surely the shaft is snapped, or the chain is seized and it took the teeth off whatever great is behind the steel bracket
×
×
  • Create New...