Jump to content
SAU Community

Recommended Posts

OK guys just need some un-biased opinions. I've come to the conclusion that I need some type of fuel management aids. By looking at the dyno sheet, you can see some real bad dips (40hp near the end). I've been told that its the ecu and its retarding when running higher boost. (correct me if im wrong, this is just what ive been told by a few people as a 'possible cause')

dynosm.jpg

I want to know basically if I should bite the bullet and just go for a power FC, or do the cheaper Super AFC II option. Also.. I can get the Power FC off these forums for about $980 delivered, but how much is this going to cost to get fitted and tuned? The SAFC II is about $400 delivered, but is this cheaper to install and tune as well?

BTW mods are

seperated dump pipe to 3" s/s exh, hks pod, man boost control, Hybrid FMIC.

Link to comment
https://www.sau.com.au/forums/topic/77715-powerfc-or-safc-ii/
Share on other sites

the boost control itself seems to be a bit dip-py aswell, floating around 10psi..

ive got 3" split dump, 3.5" exhaust, pod filter, ARC 450 FMIC, Microtech LT-12 running a pretty stock config, except its a bit flat at the start of the rev range, and i get 270RWHP

(i dont have a picture of my dyno graphy handy, but its pretty much the same as yours, except at the start it gets more power pretty quick, then midrange it flattens off, then it jumps heaps towards the end, and begins to curve down a tad near redline, peaking at 270RWHP at about 135km/h, altho it was dyno'd in 3rd gear)

so it should be safe to say you could get another ~30hp, and a more steady graph with some decent management. :(

If you want to add hp by just changing the ecu & want to modify your car later on, PowerFC. The safc will give you the right air-fuel ratio though, it's just a question of budget. What boost are you running????

If that power dip is due to retardation a SAFC won't help because it only adjusts the fuel not timing I believe.

What did Lumpy recommend as he knows his Nissans so I would go with that.

Other than that I'm another vote for the PFC.

It plugs straight in and only has to be tuned as opposed to wired up then tuned so install and tune costs may not differ that much.

Cheers for the advice guys.

bnr#@ - Had the bumper off to re-fibreglass and paint, its back on now, driving around with a big fmic in front wouldnt be too smart :D

ossie_21 - Im running about 0.8ish of a bar. The car drives smoother when running lower boost tho, not so up and down. When running about .8, it takes off good, then tapers off then takes off again a bit. Feels very slow ;)

I think I may need to just bite the bullet and buy the power FC, its just $1600ish I can't really afford to spend at this time, but yeh chances are down the track I 'may' change the turbo, so power fc will seem like a better option

Just to throw a curve ball, sorry - but have you considered the Greddy e-manage?

It starts life as a SAFC, but can be cheaply upgrade to provide FULL management. Lap top programming etc. It really is a versatile ecu, cost a little more than the SAFC, but alot cheaper than power fc, especially initial purchase.

From someone that has done the SAFCII route and then gone the PFC, I would highly recommend going straight to the PFC. I certainly wish I had. If this means driving your car more sedately and saving the extra money, do it. I was very similar to you, had funds for SAFCII but not for PFC but in my opinion, the money i spent on SAFCII + tuning was essentially wasted cause the PFC is such a better tuning option.

Also, in relation to the dips, do a basic diagnostics. I had a serious dip in one of my curves at high rpm (and when i say serious, i mean 100rwhp serious) and this turned out to be a knock sensor wire come loose which a simple diagnostics detected. Plugged it back in, took it for a tune again and no dip. It may help, it may not, but hope it does :)

Yeh .. the group buy needs like 30 people tho. HASHIRIYA on these forums is selling power fc + commander for $1020 delivered to door, then put on however much to tune it. Yeh ive read that its a DIY job for sure.

Uneekwahn - $1600 was a rough supplied fitted and tuned price (with 1yr aust warranty)

Just wondering if its worth it buying myself, fitting it, then just driving it somewhere to tune, ive been told powerfc std settings is 'safe' but dont floor it until a tune. Anyone know how much it is just to do a first tune of a powerfc? Keep in mind i won the raffle @ hyperdrive on the weekend so i got a power run and dyno tune to value of $150 ;)

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • ..this is the current state of that port. I appreciate the info help (and the link to the Earls thing @Duncan). Though going by that it seems like 1/4 then BSP'ing it and using a bush may work. I don't know where I'd be remote mounting the pressure sender... to... exactly. I assume the idea here is that any vibration is taken up by the semiflexible/flexible hose itself instead of it leveraging against the block directly. I want to believe a stronger, steel bush/adapter would work, but I don't know if that is engineeringly sound or just wishful thinking given the stupendous implications of a leak/failure in this spot. What are the real world risks of dissimilar metals here? It's a 6061 Aluminum block, and I'm talking brass or steel or SS adapters/things.
    • And if you have to drill the oil block, then just drill it for 1/4" and tap it BSP and get a 1/8 to 1/4 BSP bush. The Nissan sender will go straight in and the bush will suit the newly tapped hole. And it will be real strong, to boot.
    • No it doesn't. It just needs an ezy-out to pull that broken bit of alloy out of the hole and presto chango - it will be back to being a 1/8" hole tapped NPT. as per @MBS206 recco. That would be for making what you had in alloy, in steel. If you wanted to do just that instead of remote mounting like @Duncan and I have been pushing. A steel fitting would be unbreakable (compared to that tragically skinny little alloy adapter). But remote mounting would almost certainly be 10x better. Small engineering shops abound all over the place. A lathe and 10 minutes of time = 2x six packs.
    • Ahh. Well the block damage is a problem, you really need to run a tap or thread chaser through it to see if the threads can be saved, but any chips are likely to be bottom end bound which is bad. Earls seem to have what you need if you want to stick with mounting direct on the block: https://rceperformance.com.au/parts/earls-straight-adapter-1-8-npt-male-to-1-8-bspt-female.html, but as I said above I'd recommend remote mounting the sender
    • I'm not quite understanding or I'm missing steps here, (I appreciate people are trying to inform my brain but I am of the dumb, especially today) - All I want to do is mount the male BSPT of the OEM sender into the system somewhere without it snapping the adapter via vibration. The Nissan sender has a male 1/8 BSPT output. The block has a (very destroyed) 1/8 NPT input. I'm not really sure how a lathe assists with that, and also don't know anybody with a lathe, nor specifically what I would want to buy. I'm not really sure how adding additional adapters creates a better, more leak proof resilient seal here.
×
×
  • Create New...