Jump to content
SAU Community

Recommended Posts

  • Replies 97
  • Created
  • Last Reply

Top Posters In This Topic

  • 3 weeks later...
we MIGHT have it in before DECEMBER cant say how i know i just do.

Was supposed to arrive into the pumps at Selfs Point last month, but the safety team they set up to assess the setup deemed the setup unsatisfactory so we now have to wait a bit longer while they set everything up again to pass the safety inspection.

Oh and 98RON petty will be 2c/L dearer than ordinary 95RON petty :D.

This all came from the manager at Shell North Hobart, so it aint bullshit :D.

Link to comment
https://www.sau.com.au/forums/topic/78592-pulp-98/page/2/#findComment-1527030
Share on other sites

Ive got a Microtech LT-8, thinking about upgrading to an LT-12 but there isn't much difference except more inputs/outputs. oh and the cost factor.

Do you know Paul with the White S4/5 RX7 (think he was at the drags) pretty sure he gets ELF or C16 or something from MOTO sports on Killafaddy Rd, i am pretty sure they get all that stuff in

was your 300rwkw run made just on plain jane 95RON Premo?

Link to comment
https://www.sau.com.au/forums/topic/78592-pulp-98/page/2/#findComment-1528853
Share on other sites

yeh, MOTO get anything you want, I used to get toluene from them. Keen to want to spend that much on petrol though.

Off topic, who you getting to tune it tim? u got a new turbo yet?

Edited by phat_r33
Link to comment
https://www.sau.com.au/forums/topic/78592-pulp-98/page/2/#findComment-1529244
Share on other sites

Went into MOTO today they have 102 octane for about $90 for 20litre drum.  He said they might be getting some 110 octane he will let me know when it arrives.

be good if you could keep us posted about it mate :)

Cheers B

Link to comment
https://www.sau.com.au/forums/topic/78592-pulp-98/page/2/#findComment-1538700
Share on other sites

Yeah let me know how u go with the fuel as well, as it is now gettin to high 300's for a 200L drum of bp ultimate which i use in the gtr and i will also use it in the race car and its gettin fairly expensive for pulp fuel.

cheers matt

Edited by BLUEGTR
Link to comment
https://www.sau.com.au/forums/topic/78592-pulp-98/page/2/#findComment-1540308
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now



  • Latest Posts

    • Hi...so a "development" here aswell The swap is "done" and car went "test drive" BUT it seems the clutch(maybe gearbox?) is a little bit sad? I bought this clutch kit https://justjap.com/products/xtreme-heavy-duty-organic-clutch-flywheel-kit-nissan-skyline-r31-r32-r33-push-type "Problem" is that the first gear is hard to put into and it seems that the clutch is not disengaged. It was not the problem with the old clutch...(or like sometime the first gear would not get as easy specialy when the fluid was cold) So? Can it be like...bad "install" or is the clutch wrong ((it should not have been) i done research to get the right one) Or is this "normal" with new clutch and needs to be break in? 
    • @Duncan I can try  and thanks i did not thought about VIN and part numbers for 33/34. @GTSBoy yeah it looks like iam gonna do that  
    • Forgot to include this but this is the mid section of my steering rack that looks like it has a thread/can be turned with that notch mentioned in the post:
    • Hey everyone, Wanted to pick some brains about this issue I'm having with rebuilding my 33 rack (PN is 49001-19U05). All of the tutorials/videos I've seen online are either R34 or S Chassis racks which seem to be pretty straightforward to disassemble but this process doesnt carry over to my rack. Few of the key differences that I've noted The pinion shaft on the other racks bolt on with 3 torx bolts: Whereas my rack bolts on with 2 allen head bolts: These changes are pretty inconsequential but the main difference is how you pull the actual rack out of the housing. The other skyline/s chassis racks can be taken out by tapping the rack out of the body with a socket and it just slides right out. I'm unable to do that with my rack because there's a hard stop at the end that doesn't let the seal/shaft be tapped out. Can also see a difference in the other end of the rack where mine has a notch that looks like you're able to use a big wrench to unthread 2 halves of the rack whereas the other racks are just kinda set in with a punch. My rack: Other racks: TLDR; Wanted to know if anyone has rebuilt this specific model of steering rack for the R33 and if there were any steps to getting it done easier or if I should just give this to a professional to get done. Sorry if this post is a bit messy, first one I've done.
    • I would just put EBC back on the "I would not use their stuff" pile and move on.
×
×
  • Create New...