Jump to content
SAU Community

R33 Gtr Wheels

lowflyer
 Share

Recommended Posts

lowflyer Enthusiast

lowflyer

Posted
Posted

Have a set of R33 GTR wheels for sale with Yokohama race tyres. Rims have some paint chips on outer edge otherwise they are in very good shape, tyres have only approx. 20% tread left.

Looking for around $1700 and I am willing to trade a cheaper set of rims. I am looking for some 17" or 18" rims for my Corvette also so let me know what you have.

Thanks.

Link to comment
https://www.sau.com.au/forums/topic/78663-r33-gtr-wheels/
Share on other sites
Guest two.06l

Guest two.06l

Posted
Posted
Have a set of R33 GTR wheels for sale with Yokohama race tyres. Rims have some paint chips on outer edge otherwise they are in very good shape, tyres have only approx. 20% tread left.

Looking for around $1700 and I am willing to trade a cheaper set of rims. I am looking for some 17" or 18" rims for my Corvette also so let me know what you have.

Thanks.

what are the tyres??? could be interested

Link to comment
https://www.sau.com.au/forums/topic/78663-r33-gtr-wheels/#findComment-1437209
Share on other sites
  • 4 weeks later...
lowflyer Enthusiast

lowflyer

Posted
  • Author
Posted
Will u sell rims cheaper without tyres? Are the tyres good?

I didn't put a lot of value on the tyres (even though they cost over $400 each new) as they only have around 20% tread left on them. I'll think about selling the rims separately if I don't have any luck in the next week or so.

Link to comment
https://www.sau.com.au/forums/topic/78663-r33-gtr-wheels/#findComment-1483561
Share on other sites
  • 2 years later...
Guest
This topic is now closed to further replies.
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • The Bogan
      NC MX5

      By The Bogan · Posted

      The final part arrived today to un-clampify and simplify the intake Who would have though a 1/2" hose stainless bulkhead fitting designed for below waterline bilge pumps would be what I needed Test fit on a 3" offcut I had laying around to see if it would work, and it worked a treat All going well the intake will be on its "final version" tomorrow 
    • Komdotkom
      R32 Gtst - Track Car

      By Komdotkom · Posted

      Good luck on the weekend mate
    • Duncan
      From Japan and back to Europe, my sh*tbox R34 GTT

      By Duncan · Posted

      Must have been an absolute nightmare to drive when the power steer was out, the rack ratio/wheel size/caster is all set up for power assistance
    • Duncan
      New

      By Duncan · Posted

      Welcome to SAU, what are you looking at buying?
    • GabsReDeal
      R32 GTS (RB20DE) Injectors Replacement

      By GabsReDeal · Posted

      I checked the injectors again (1 and 2, since they’re easiest to access) to make sure they weren’t clogged. Even though the entire fuel system had been cleaned, I wanted to be certain. Everything looked clean, so I reinstalled and connected everything. When I started the car to confirm everything was okay, it immediately revved up high, so I shut it off straight away. I checked to see if I’d missed a vacuum hose or something, but everything was connected. On the second attempt, the car ran without the high idle, but I noticed a distinct “compressed air” sound coming from the engine bay. Tracing the sound, I pushed injector #6 forward slightly and the noise stopped — it turned out it wasn’t seated properly, despite the fuel rail being bolted down. While holding it in place, the car idled steadily without stalling and ran for over 5 minutes. At this point, I pulled all six injectors out just in case I hadn’t seated them correctly or dirt had gotten onto the O-rings. Unfortunately, I discovered that I had damaged 3 out of 6 injectors (the OEM 270cc ones) during installation. So yes, this was my fault. Since only the pintle caps were damaged, I’ve ordered a Fuel Injector Service Kit from NZEFI to refurbish them. In the meantime, I reinstalled my new injectors – the car now idles fine for over 15 minutes without stalling. I have not attempted to drive it so far. It’s not perfect yet, as it hesitates when the throttle is pressed, but it’s a big improvement. Unplugging the IACV with the new injectors idles at around 800rpm, even with the IACV screw tightened fully. But this is probably due to tune.
×
×
  • Create New...