Jump to content
SAU Community

Recommended Posts

hey

my thermo died so it had been replaced but the car is now running much cooler then it originally was, these days its lucky to get upto 70deg (damn winter) whilst it was originally running at approx 85 deg. can this cause

bad fuel consumption ?

loss of power ?

engine damage ?

i'm just wondering cause i was looking at the water temp correction tables in the PFC and noticed that the only place where its set to 1.00 is at 80 deg +++

but if my water temp doesn't reach 80deg + then it'll always be treating the engine as if its still warming up..... should i get the thermo adjusted or can i just set the settings in the PFC to 1.00 for water temps at 60 deg +

also in the correciton tables there are 2 columns i assume one is for A/C on and the other for A/C off, but am unsure....

please help :confused: :confused: :confused:

Link to comment
https://www.sau.com.au/forums/topic/78873-can-an-engine-run-too-cold/
Share on other sites

Most thermos do not cool as well as the standard clutch fan. After people install thermos, they usually notice that the temps run hotter.

Therefore, you're setup should be alright, because if you were running the stock fan, it would be even cooler (that is, assuming that you have the same setup - i.e. it switches on at the same temp etc).

Your best bet is to re-calibrate your thermo fan controller to turn on later and keep your water temp between 75-85degC

Anything less and really it just causes engine wear and tear.

I would be looking to run 1.00 or no extra fuel anything above 70degC, anything below this and it will require extra fuel for smooth running.

well i had a fiddle with the PFC, turned down the 50 deg value in the PFC, seems to be runnign ok, its hard to tell nowhere to get up into 4th gear and wheelspin city thru 1,2, and a bit of 3, so hopefully tommorow will be cold and dry and we'll see, how can i find out how the thermo is set ???

got up to 70 deg quickly tonight on the way home and hovered there not until i put the boot in (3 short boosts in 3rd) did it start to climb and only upto 74 deg, then slowly dropped again......

Most definitely yes.

All metals expand. Aluminium-alloys much more & faster than iron-steel. All engines are machined to calculated clearances for the material composition of the components, so running cool it will not allow enough expansion & most components will wear faster. Also, most alloy headed engines produce maximum power between 82 - 90 deg. c. This is ofcourse as long as the gauge is accurate & measureing the temp. of the water exiting the head. Don't confuse low engine temps. with low charge air temps.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Cheers. Skyline is back on the menu, can’t get rid of it. It’s like a child you don’t want, or herpes 
    • I got back to Japan in January and was keen to get back on track as quickly as possible. Europe is god-awful for track accessibility (by comparison), so I picked up a first-gen GT86 in December just to have something I could jump into right away. The Skyline came over in a container this time and landed in early January. It was a bit battered after Europe, though—I refused to do anything beyond essential upkeep while it was over there. The clutch master cylinder gave out, and so did the power steering. I didn’t even bother changing the oil; it was the same stuff that went in just before I left Japan the first time. Naughty. Power steering parts would’ve cost double with shipping and taxes, so knowing I’d be heading back to Japan, I just postponed it and powered through the arm workout. It took a solid three months to get the car back on the road. Registration was a nightmare this time around. There were a bunch of BS fees to navigate, and sourcing parts was a headache. I needed stock seats for shaken, mistakenly blew 34k JPY on some ENR34 seats—which, of course, didn’t fit—then ended up having the car’s technical sheet amended to register it as a two-seater with the Brides. Then there’s the GT86. Amazing car. Does everything I want it to do. Parts are cheap, easy to find, and I don’t care what anyone says—it’s super rewarding to drive. I’ve done a few basic mods: diff ratio, coilovers, discs, pads, seat, etc. It already had a new exhaust manifold and the 180kph limiter removed, so I assume it’s running some kind of map. I’ve just been thrashing it at the track non-stop—mostly Fuji Speedway now, since I need something with higher speed after all that autobahn time. The wheels on the R34 always pissed me off—too big, and it was a nightmare getting tires to fit properly under the arches. So I threw in the towel and bought something that fits better. Looks way cleaner too (at least to me)—less hotboy, less attention-seeking. Still an R34, though. Now for future plans. There are a few things still outstanding with the car. First up, the rear subframe needs an overhaul—that’s priority one. Next, I need to figure out an engine rebuild plan. No timeline yet, but I want to keep it economical—not cutting corners, just not throwing tens of thousands at a mechanic I can barely communicate with. And finally, paint. Plus a bit of tidying up here and there.  
    • Nope, needed to clearance under the bar a little with a heat gun, a 1/2" extension as the "clearancer", and big hammer, I was aware of this from the onset, they fit a 2.0 with this intake no problems, but, the 2.5 is around 15mm taller than a 2.0, so "clearancing" was required  It "just" touched when test fitting, now, I have about 10mm of clearance  You cannot see where it was done, and so far, there's no contact when giving it the beans Happy days
    • It's been a while since I've updated this thread. The last year (and some) has been very hectic. In the second-half of 2024 I took the R34 on a trip through Germany, Italy, France and Switzerland - it was f*cking great. I got a little annoyed with the attention the car was getting around Europe and really didn't drive it that much. I could barely work on the car since I was living in an inner-city apartment (with underground parking). During the trip, the car lost power steering in France - split hose - and I ended up driving around 4,000kms with no power steering.  There were a few Nurburgring trips here and there, but in total the R34 amassed just shy of 7,000kms on European roads. Long story short, I broke up with the reason I was transferred to Europe for and requested to be moved back to Japan. The E90, loved it. It was a sunk cost of around EUR 10,000 and I sold it to a friend for EUR 1,500 just to get rid of it quickly. Trust me, moving countries f*cking sucks and I could not be bothered to be as methodical as I was the first time around.
×
×
  • Create New...