Jump to content
SAU Community

Recommended Posts

Chris,

How was the O2's response (0.2-0.8v cycle speed) affected with the change ON IDLE? If the lag time is out the closed loop function finds it hard to cycle quickly.

Edited by Cubes

Didn't check that as yet mate, will have a look tonight

Economy has been quite poor for a while now, hope its a bit better now

Edited by Chris32

i've been running my car with closed loop disable for about a month now and i'm getting 300-350km per tank with city driving only. I find when i enable closed loop my idle becomes jumpy. Possibly stuffed o2 sensor

Chris,

How was the O2's response (0.2-0.8v cycle speed) affected with the change ON IDLE? If the lag time is out the closed loop function finds it hard to cycle quickly.

Checked this on the way to work today, response was very quick

Never checked it before though

Economy seems to be a bit better too

  • 1 month later...

Mine is still giving me the shits

Playing around with injector correction % on each injector now. Last night I went through each injector and added 2% more fuel to see if it would help with my random knock

Injector 4 showed the most improvement, knock going from 80 to 24 at 1.3bar

so now my injector correction reads

1 59.5%

2 58.5%

3 58.5%

4 60.5%

5 59.0%

6 59.5%

Maybe I am finally onto what my problem is?

Worst knock I saw on the way to work this morning was 33. It used to be up in the 70's

Running SAFF 98 with 10% ethanol. The fuel itself showed normal knock numbers compared to BP98 before I did the adjustments

Edited by Chris32

The car feels and sounds allot better. Maybe its just me, but the exhaust sounds crisper than before

The injectors were cleaned and tested a year ago, and where all within 1% of eachother. There was one which was a bit clogged, but it all was ok

Will see how it goes in the next few days

If only we could tell which knock sensor reads what. :P

Chris, If it is indeed pinging slightly and has been for some time then those little rb20's are tough little nuggets to crack.

Edited by Cubes

I've done that mod.. it doesn't appear to make any difference to how the bov opens or when it opens.

I did find drivability to suffer a little when cruising around the hills. Made the car jerk around more when you jump off and on part throttle. Depending it may also increase the chances surge.

So.. I removed the grub.

Edited by Cubes
If only we could tell which knock sensor reads what. :)

Chris, If it is indeed pinging slightly and has been for some time then those little rb20's are tough little nuggets to crack.

Yeah, I think it probably is detonation, how much is hard to gather

Been like that for over a year now, close to 18,000kms!

Will keep going in the process of elimination to see what differance more of a play with the injectors does

BOV mod works well on mine, does make on off throttle driving a little harder to keep smooth

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Yeah, it's getting like that, my daughter is coming over on Thursday to help me remove the bonnet so I can install the Carbuilders underbonnet stuff,  I might get her to give me a hand and remove the hardtop, maybe, because on really hot days the detachable hardtop helps the aircon keep the interior cool, the heat just punches straight through to rag top I also don't have enough hair for the "wind in the hair" experience, so there is that....LOL
    • Could be falling edge/rising edge is set wrong. Are you getting sync errors?
    • On BMWs what I do because I'm more confident that I can't instantly crush the pinch welds and do thousands of USD in chassis damage is use a set of rubber jacking pads designed to protect the chassis/plastic adapter and raise a corner of the car, place the aforementioned 2x12 inch wooden planks under a tire, drop the car, then this normally gives me enough clearance to get to the front central jack point. If you don't need it to be a ramp it only needs to be 1-1.5 feet long. On my R33 I do not trust the pinch welds to tolerate any of this so I drive up on the ramps. Before then when I had to get a new floor jack that no longer cleared the front lip I removed it to get enough clearance to put the jack under it. Once you're on the ramps once you simply never let the car down to the ground. It lives on the ramps or on jack stands.
    • Nah. You need 2x taps for anything that you cannot pass the tap all the way through. And even then, there's a point in response to the above which I will come back to. The 2x taps are 1x tapered for starting, and 1x plug tap for working to the bottom of blind holes. That block's port is effectively a blind hole from the perspective of the tap. The tapered tap/tapered thread response. You don't ever leave a female hole tapered. They are supposed to be parallel, hence the wide section of a tapered tap being parallel, the existince of plug taps, etc. The male is tapered so that it will eventually get too fat for the female thread, and yes, there is some risk if the tapped length of the female hole doesn't offer enough threads, that it will not lock up very nicely. But you can always buzz off the extra length on the male thread, and the tape is very good at adding bulk to the joint.
    • Nice....looking forward to that update
×
×
  • Create New...