Jump to content
SAU Community

need a strong clutch

2BNVS
 Share

Recommended Posts

B33st Community Regular

B33st

Posted
Posted

Just had Jim berry rebuild my existing clutch for $850 to suit my current approx 320rwkw build. Used my existing preasue plate but rebuilt and upped the clamping presure from 2200lbs to 3400lbs, 5 puk carbotic clutch plate made from an exedy nissan patrol center. Cost also incuded machining my standard fly wheel. This guy is awesome he explains everything to you and will find out exactly what you want.

Shaun Mentor

Shaun

Posted
Posted

Dont be fooled by people telling you your dreaming if you dont go a twin plate. Jim Berry is the clutch god. He'll build you a single plate that'll hold that sort of power easy. He built a 4000lb modified Nismo 5 puck for my r33 gtr engined gtst for $850. All people in the know seem to recommend him from experience too.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
 Share
Go to topic listing


  • Similar Content

  • Latest Posts

    • Erelyes
      Ceramic turbine damage to engine - what did yours do?

      By Erelyes · Posted

      Ha, well, it's been.... a bit of a journey. Things have taken much longer than I'd hoped. I'll probably put up a thread at some stage. Hopefully soon. The car's not done any kms since my update in June though, put it that way.
    • Dose Pipe Sutututu
      M35 Aftermarket Fuel Pump

      By Dose Pipe Sutututu · Posted

      Here's the chart for fuel pressure vs. current draw, assuming your base fuel pressure is 3 bar and you run like 0.5bar boost on WOT, you should only momentarily hit 9amps here and there. (Ignore my prev post, I cannot read a chart these days it seems)
    • GTSBoy
      RB25 Drama's

      By GTSBoy · Posted

      Those comp test results are not hideous. Whether they are accurate or not (ie, when that comp tester says 140 psi, is the real pressure120, 140 or 160?) is unknown to us. The state of the battery used to crank it over is unknown, etc etc. Many people around here would say that the absolute values and the spread are perfectly fine to just add boost and keep going. I personally would be happier with a narrower spread than that, but even the diff between 125 and 145 is not terrible. That one cylinder at 125 though, has probably copped some damage relative to the others. You should inspect the valves seeing as you've got it open. Do you know how to measure installed ring gaps? That, and an inspection of the rings themselves, is how you will determine whether they need to be replaced. If you're not good to do these things, take the block and the pistons and rings to a shop that is, and ask them for the go/no-go on them. Do the bores need a hone at all? If so, you might well be justified in getting some different pistons in order to get away from the ring supply problem. Whether you're happy to spend a lot more money right now, on more gear, rather than less money, but an amount that looks stupid given that you will only get a handful of rings in exchange for that money, is for you to decide.
    • iain_ST44GA
      M35 Aftermarket Fuel Pump

      By iain_ST44GA · Posted

      also possibly backed up to my filler and shat down it! 🤣
    • Julsmadrid
      RB25 Drama's

      By Julsmadrid · Posted

      Ok so i would love some advice here please, i purchased an R33 a few months back and its had a few mods done to the engine, its an RB25det running a Master ECU, 1200cc injectors, bigger turbo, oil cooler, oil filter relocation kit, Spool H-beam rods, acl/ross pistons. When i removed the motor from the vehicle (as its getting a respray) i thought i would compression test it and these are the following results. Cylinder 1-145psi, Cylinder 2-143psi, Cylinder 3-125psi, Cylinder 4-145psi, Cylinder 5-140psi, Cylinder 6-135psi this test was done with the motor on the ground and powering up the starter motor. I dropped the sump and found broken oil squirters on cylinder 3,5 and 6. I was told my rings are probably worn so i stripped the motor completely to get a new set of rings for it. The trouble is no one has these rings anywhere and they have to be custom made by Ross over in the states and will cost about $600+$200 delivery. My question is how can i tell if my rings are at fault and if they are still ok and is this price ok for a set of rings?
×
×
  • Create New...