Jump to content
SAU Community

Recommended Posts

wrxhoon,

   Nice time, I think with the clutch you should bed down a flat 12. I will be there once I get my clutch in. What tyres did you run?

Yea i should be able to run a flat 12 or even a high 11 with a good clutch , i will be looking for a Nismo twin plate i think .

Toyo 265x35x18 in the stock 18x9 rims and full street pressure ( 38 psi ) . traction wasn't a problem , the clutch wouldn't grab at any amount of rpm , i even went down to 2500 for a 2.37 60 ft .

What kind of clutch are you going for ?

Jerry have you listed your mods so far on the M-Spec? Nice time with the stock clutch. Mine is slipping at high rpm launches as well but i figured that was expected with 70k kms done on it.

I'm heading to Japan (tommorrow) to load up two suitcases with stuff. Here's praying customs dont notice.

Jerry have you listed your mods so far on the M-Spec? Nice time with the stock clutch. Mine is slipping at high rpm launches as well but i figured that was expected with 70k kms done on it.

I'm heading to Japan (tommorrow) to load up two suitcases with stuff. Here's praying customs dont notice.

My clutch was holding 100% on road and while tuned , its just when you sidestep @ 5000 + to much heat in to it and then it would kepp slipping especialy on gear changes . On my last run i only used about 4500 ( not enough realy for a clean launch ) and that was my best run .

Mods are as i told you before , gtss's , p f/c , 550 cc Nismo injectors , hard i/c pipping , ( stock i/c ) pod filters ,( for now , still looking for a stock airbox ) ebc ( 1.2 bar) , hks front pipes ,( stock dumps , they are s/s on the 34 ) 3" catback ( very quiet )and thats about it . Its a very responsive car with that set up .

How long are you in Japan for ? good luck with the shopping list .

Check your p.m

I was out there watching as per normal.

Some people just don't get it. There must have been atleast 15 different cars that had no idea how to stage!! It just holds up the whole night.

Highlight of the night was the dark red s14 throwing a good burnout all the way up to the staging line and then hitting the starter when he came over to tell him off.

Good to see some r32 gtst's out.

The inability to stage thing really pisses me off. It shows that they clearly have either never been to WSID to watch others race, or they have watched but failed to pay any attention.

That red S14 thing was quite funny. Yay lets stand directly infront of a car that's doing a burnout to teach him a lesson, oh shit he ran into me. Quite suprised the driver didn't get out and give him a mouthful. It was only about 15mins earlier the announcers said over the PA "Do not do a burnout across the line, we don't care how big your burnout is before the line but don't go over it".

From what I could see he hadn't passed the line yet :D

Yes that's right.

As you approach the line you will see on either side of your lane (the red painted bit) a narrow white line (which is actually about 20-30cm wide I believe). Slowly moving in will initiate the first 'pre-stage' light, moving forward a few cm again will initiate the 2nd light (you are now ready to race).

If you happen to roll too far forward and the 1st 'pre-stage' light goes out but the 2nd staging light stays on don't panic just stay where you are. It just means that you can't move forward anymore otherwise you will breakout (red light = disqualified).

Many people make the mistake of quickly trying to reverse back and then drive forward again into stage however before they can do that the 'starter' has already started the staging sequence and you'll screw up your run and timing.

Their is 0.4sec between each of the yellow/amber lights before the green lights up. I usually release the clutch when I seen the 2nd (of 4) amber lights 'go out'. From this I was getting consistent 0.1-0.2sec reaction times (which don't effect your time on wednesday nights but it's the easiest way to beat any car you are racing against).

Many people make the mistake of quickly trying to reverse back and then drive forward again into stage however before they can do that the 'starter' has already started the staging sequence and you'll screw up your run and timing.

yep,i done that. practise makes perfect i guess.

ill be getting there at 5pm next time,way too many cars.

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now


  • Similar Content

  • Latest Posts

    • Thanks for doing that Duncan! Makes you a good person in my books. We don't get kangaroos or wombats here. But we have bats and it's similar. AFAIK it's often the mums with a baby attached that get hit because they drop lower when starting from a tree. If you hit an animal, check on it. https://www.ifaw.org/au/resources/wildlife-rescue-app An app to get the closest wildlife rescue contact.
    • My dream is also to have a proper hoist, but I don't think it will ever happen. My quickjack is probably as close as I'll ever get, it really is very good though. 
    • Yeah we keep on in the dailies, it is pretty poor how many animals get hit and the driver leaves without checking....have saved a couple of little ones over the years. Bit of a gruesome job though, pouches generally need to be cut open because they are so tight and often the joey doesn't realise mum is gone so they are still locked onto the teat. I checked the modules in front of the DS wheel where an oil cooler should go.... There is the radar unit - that can go for race use) One of the 2 HX water pumps, the silver cylinder. That needs to be kept but might be able to be relocated But the bad news, the big computer mounted vertically in front of the wheel (blocking any potential air exit) is the electric steering computer. That is required until/unless i do a hydraulic steering conversion, and in CAD based modern car design it is not like I can just pop a big unit like that somewhere else (plus the loom would be too short anywhere else too). So, the passenger side is OK to clear out (just use a smaller washer reservoir, potentially elsewhere), but the DS no beuno
    • Well, all the best with the new camry It was interesting to hear about the UK process, it is generally a lot more streamlined here with a shipping agent looking after all the import side (noting the exact final price can still be a surprise.....) and I've used a few different brokers on the japan (or US) side, and never had any trouble with any of them....luck of the draw I guess. You mentioned you didn't get the auction sheet (understandable since you bought it from a dealer, not auction), but I always try and get hold of that because they are pretty thorough. I've imported 2x R grade vehicles over the years and both were fine, repairs in Japan are pretty thorough compared to here in Oz.
    • BTW I measured the jack I have, it is 70mm at the saddle but you only have about 700 until it returns to 150mm high at the cylinder so it is good but no magic bullet.
×
×
  • Create New...